Multi Point Fuel Injection System

September 14, 2017 | Author: Goutham Reddy | Category: Fuel Injection, Throttle, Internal Combustion Engine, Carburetor, Vehicle Technology
Share Embed Donate


Short Description

Download Multi Point Fuel Injection System...

Description

MULTI –POINT FUEL INJECTION

Contents Chapters

Page No.

Introduction

3

Objectives

5

History and Development

6

Supersession of carburetor

10

Basic function

13

Fundamentals of fuel injection

15

Various injection system

18

Conclusion

22

Reference

23

Introduction I was commuting with my friends back from college one evening when one of them asked me: What is an MPFI Engine? 2

You must have seen cars with specifications which mention words like MPFI and CRDI or CRDE. To an automotive engineer or enthusiast, it means something, but for a common man, it may not make much sense. MPFI means – Multi-point Fuel-Injection (also called fuel-injection system)

The term MPFI is used to specify a technology used in Gasoline/petrol Engines. For Diesel Engines, there is a similar technology called CRDI. MPFI System is a system which uses a small computer to control the Car’s Engine. A Petrol car’s engine usually has three or more cylinders or fuel burning zones. So in case of an MPFI engine, there is one fuel –injector installed near each cylinder, that is why they call it Multi-point (more than one points) Fuel Injection. In plain words, to burn petrol in an Engine to produce power, Petrol has to be mixed with some air, ignited in a cylinder (also called combustion chamber), which produces energy and runs the engine. 3

Before MPFI system was discovered, there was a technology called “Carburetor”. Carburetor was one chamber where petrol and air was mixed in a fixed ratio and then sent to cylinders to burn it to produce power. This system is purely a mechanical machine with little or no intelligence. It was not very efficient in burning petrol; it will burn more petrol than needed at times and will produce more pollution. But with the advancement of technology this was about to change. Based on various inputs from the sensors, the computer in the MPFI system decides what amount of fuel to inject. Thus it makes it fuel efficient as it knows what amount of petrol should go in. To make things more interesting, the system also learns from the drivers driving habits. Modern car’s computers have memory, which will remember your driving style and will behave in a way so that you get the desired power output from engine based on your driving style. For example, if you have a habit of speedy pick-up, car’s computer will remember that and will give you more power at low engine speeds by putting extra petrol, so that you get a good pick-up. It will typically judge this by the amount of pressure you put on accelerator. So the cars of today are really intelligent, well not as intelligent as drivers but fairly intelligent to keep pollution under control and saving the fuel.

Objectives The functional objectives for fuel injection systems can vary. All share the central task of supplying fuel to the combustion process, but it is a design decision how a particular system will be optimized. There are several competing objectives such as: 4

• • • • • • • • • • •

power output fuel efficiency emissions performance ability to accommodate alternative fuels reliability driveability and smooth operation initial cost maintenance cost diagnostic capability range of environmental operation Engine tuning

History and Development Herbert Akroyd Stuart developed the first system laid out on modern lines to meter out fuel oil at high pressure to an injector. This system was used on the hot bulb engine and was adapted and improved by Robert Bosch for use on diesel engines. The first use of direct gasoline injection was on the Hesselman engine invented by Swedish engineer Jonas Hesselman in 1925. Hesselman engines use the ultra lean burn principle; fuel is injected toward the end of the compression stroke, and then ignited with a spark plug. They are often 5

started on gasoline and then switched to diesel or kerosene. Fuel injection was in widespread commercial use in diesel engines by the mid-1920s. Because of its greater immunity to wildly changing g-forces on the engine, the concept was adapted for use in gasoline-powered aircraft during World War II, and direct injection was employed in some notable designs like the Junkers Jumo 210, the Daimler-Benz DB 601, the BMW 801, the Shvetsov ASh-82FN (M-82FN) and later versions of the Wright R-3350 used in the B-29 Superfortress.

Mechanical The term Mechanical when applied to fuel injection is used to indicate that metering functions of the fuel injection (how the correct amount of fuel for any given situation is determined and delivered) is not achieved electronically but rather through mechanical means alone. In the 1940s, hot rodder Stuart Hilborn offered mechanical injection for racers, salt cars, and midgets. One of the first commercial gasoline injection systems was a mechanical system developed by Bosch and introduced in 1952 on the Goliath GP700 and Gutbrod Superior 600. This was basically a high pressure diesel directinjection pump with an intake throttle valve set up. This system used a normal gasoline fuel pump, to provide fuel to a mechanically driven injection pump, which had separate plungers per injector to deliver a very high injection pressure directly into the combustion chamber.

Goliath GP700

Carrera 3.0

6

Another mechanical system, also by Bosch, but injecting the fuel into the port above the intake valve was later used by Porsche from 1969 until 1973 for the 911 production range and until 1975 on the Carrera 3.0 in Europe. Porsche continued using it on its racing cars into the late seventies and early eighties. Chevrolet introduced a mechanical fuel injection option, made by General Motors' Rochester Products division, for its 283 V8 engine in 1956 (1957 US model year). This system directed the inducted engine air across a "spoon shaped" plunger that moved in proportion to the air volume. This system was not a "pulse" or intermittent injection, but rather a constant flow system, metering fuel to all cylinders simultaneously from a central "spider" of injection lines. The fuel meter adjusted the amount of flow according to engine speed and load, and included a fuel reservoir, which was similar to a carburetor's float chamber. With its own high-pressure fuel pump driven by a cable from the distributor to the fuel meter, the system supplied the necessary pressure for injection. This was "port" injection, however, in which the injectors are located in the intake manifold, very near the intake valve. The highest performance version of the fuel injected engine was rated at 283 bhp (211.0 kW) from 283 cubic inches (4.6 L). This made it among the early production engines in history to exceed 1 hp/in³ (45.5 kW/L), after Chrysler's Hemi engine and a number of others. During the 1960s, other mechanical injection systems such as Hilborn were occasionally used on modified American V8 engines in various racing applications such as drag racing, oval racing, and road racing. These racingderived systems were not suitable for everyday street use, having no provisions for low speed metering or even starting. However they were a favorite in the aforementioned competition trials in which essentially wideopen throttle operation was prevalent.

Electronic The first commercial electronic fuel injection (EFI) system was Electrojector, developed by the Bendix Corporation and was to be offered by American Motors (AMC) in 1957. A special muscle car model, the Rambler Rebel, showcased AMC's new 327 cu in (5.4 L) engine. The Electrojector was an option and rated at 288 bhp (214.8 kW). With no Venturi effect or heated carburetor (to help vaporize the gasoline) AMC's EFI equipped engine breathed easier with denser cold air to pack more 7

power sooner and it reached peak torque 500 rpm quicker. This was to have been the first production EFI engine, but Electrojector's teething problems meant only pre-production cars were so equipped: thus, very few cars so equipped were ever sold and none were made available to the public. The EFI system in the Rambler was a far more-advanced setup than the mechanical types then appearing on the market and the engines ran fine in warm weather, but suffered hard starting in cooler temperatures.

Rambler Rebel

1958 Chrysler 300D

Chrysler offered Electrojector on the 1958 Chrysler 300D, Dodge D500, Plymouth Fury, and DeSoto Adventurer, arguably the first series-production cars equipped with an EFI system. It was jointly engineered by Chrysler and Bendix. The early electronic components were not equal to the rigors of underhood service, however, and were too slow to keep up with the demands of "on the fly" engine control. Most of the 35 vehicles originally so equipped were field-retrofitted with 4-barrel carburetors. The Electrojector patents were subsequently sold to Bosch. Bosch developed an electronic fuel injection system, called D-Jetronic (D for Druck, German for "pressure"), which was first used on the VW 1600TL/E in 1967. This was a speed/density system, using engine speed and intake manifold air density to calculate "air mass" flow rate and thus fuel requirements. This system was adopted by VW, Mercedes-Benz, Porsche, Citroën, Saab, and Volvo. Lucas licensed the system for production with Jaguar.

8

Bosch superseded the D-Jetronic system with the K-Jetronic and L-Jetronic systems for 1974, though some cars (such as the Volvo 164) continued using D-Jetronic for the following several years. The Cadillac Seville was introduced in 1975 with an EFI system made by Bendix and modeled very closely on Bosch's D-Jetronic. L-Jetronic first appeared on the 1974 Porsche 914, and uses a mechanical airflow meter (L for Luft, German for "air") that produces a signal that is proportional to "air volume". This approach required additional sensors to measure the atmospheric pressure and temperature, to ultimately calculate "air mass". L-Jetronic was widely adopted on European cars of that period, and a few Japanese models a short time later. In 1982, Bosch introduced a sensor that directly measures the air mass flow into the engine, on their L-Jetronic system. Bosch called this LH-Jetronic (L for Luftmasse and H for Hitzdraht, German for "air mass" and "hot wire", respectively). The mass air sensor utilizes a heated platinum wire placed in the incoming air flow. The rate of the wire's cooling is proportional to the air mass flowing across the wire. Since the hot wire sensor directly measures air mass, the need for additional temperature and pressure sensors is eliminated. The LH-Jetronic system was also the first fully-digital EFI system, which is now the standard approach. The advent of the digital microprocessor permitted the integration of all power train sub-systems into a single control module.

Supersession of carburetors The ultimate combustion goal is to match each molecule of fuel with a corresponding number of molecules of oxygen so that neither has any molecules remaining after combustion in the engine and catalytic converter. Such a balanced condition is known as stoichiometry. Extensive carburetor modifications and complexities were needed to approach stoichiometric engine operation in order to comply with increasingly-strict exhaust emission regulations of the 1970s and 1980s. This increase in complexity gradually eroded and then reversed the simplicity, cost, and packaging advantages carburetors had traditionally offered over fuel injection systems.

9

There are three primary types of toxic emissions from an internal combustion engine: Carbon Monoxide (CO), unburnt hydrocarbons (HC), and oxides of nitrogen (NOx). CO and HC result from incomplete combustion of fuel due to insufficient oxygen in the combustion chamber. NOx, in contrast, results from excessive oxygen in the combustion chamber. The opposite causes of these pollutants makes it difficult to control all three simultaneously. Once the permissible emission levels dropped below a certain point, catalytic treatment of these three main pollutants became necessary. This required a particularly large increase in fuel metering accuracy and precision, for simultaneous catalysis of all three pollutants requires that the fuel/air mixture be held within a very narrow range of stoichiometry. The open loop fuel injection systems had already improved cylinder-to-cylinder fuel distribution and engine operation over a wide temperature range, but did not offer sufficient fuel/air mixture control to 10

enable effective exhaust catalysis. Closed loop fuel injection systems improved the air/fuel mixture control with an exhaust gas oxygen sensor. The O2 sensor is mounted in the exhaust system upstream of the catalytic converter, and enables the engine management computer to determine and adjust the air/fuel ratio precisely and quickly. Fuel injection was phased in through the latter '70s and '80s at an accelerating rate, with the US, French and German markets leading and the UK and Commonwealth markets lagging somewhat, and since the early 1990s, almost all gasoline passenger cars sold in first world markets like the United States, Canada, Europe, Japan, and Australia have come equipped with electronic fuel injection (EFI). Many motorcycles still utilize carbureted engines, though all current high-performance designs have switched to EFI. Fuel injection systems have evolved significantly since the mid-1980s. Current systems provide an accurate, reliable and cost-effective method of metering fuel and providing maximum engine efficiency with clean exhaust emissions, which is why EFI systems have replaced carburetors in the marketplace. EFI is becoming more reliable and less expensive through widespread usage. At the same time, carburetors are becoming less available, and more expensive. Even marine applications are adopting EFI as reliability improves. Virtually all internal combustion engines, including motorcycles, off-road vehicles, and outdoor power equipment, may eventually use some form of fuel injection.

11

FUEL INJECTION SYSTEM

The carburetor remains in use in developing countries where vehicle emissions are unregulated and diagnostic and repair infrastructure is sparse. Fuel injection is gradually replacing carburetors in these nations too as they adopt emission regulations conceptually similar to those in force in Europe, Japan, Australia and North America.

Basic Function The process of determining the necessary amount of fuel, and its delivery into the engine, are known as fuel metering. Early injection systems used mechanical methods to meter fuel (non electronic, or mechanical fuel injection). Modern systems are nearly all electronic, and use an electronic solenoid (the injector) to inject the fuel. An electronic engine control unit calculates the mass of fuel to inject. Modern fuel injection schemes follow much the same setup. There is a mass airflow sensor or manifold absolute pressure sensor at the intake, typically mounted either in the air tube feeding from the air filter box to the throttle body, or mounted directly to the throttle body itself. The mass airflow sensor 12

does exactly what its name implies; it senses the mass of the air that flows past it, giving the computer an accurate idea of how much air is entering the engine. The next component in line is the Throttle Body. The throttle body has a throttle position sensor mounted onto it, typically on the butterfly valve of the throttle body. The throttle position sensor (TPS) reports to the computer the position of the throttle butterfly valve, which the ECM uses to calculate the load upon the engine. The fuel system consists of a fuel pump (typically mounted in-tank), a fuel pressure regulator, fuel lines (composed of either high strength plastic, metal, or reinforced rubber), a fuel rail that the injectors connect to, and the fuel injector(s). There is a coolant temperature sensor that reports the engine temperature to the ECM, which the engine uses to calculate the proper fuel ratio required. In sequential fuel injection systems there is a camshaft position sensor, which the ECM uses to determine which fuel injector to fire. The last component is the oxygen sensor. After the vehicle has warmed up, it uses the signal from the oxygen sensor to perform fine tuning of the fuel trim. The fuel injector acts as the fuel-dispensing nozzle. It injects liquid fuel directly into the engine's air stream. In almost all cases this requires an external pump. The pump and injector are only two of several components in a complete fuel injection system. In contrast to an EFI system, a carburetor directs the induction air through a venturi, which generates a minute difference in air pressure. The minute air pressure differences both emulsify (premix fuel with air) the fuel, and then acts as the force to push the mixture from the carburetor nozzle into the induction air stream. As more air enters the engine, a greater pressure difference is generated, and more fuel is metered into the engine. A carburetor is a self-contained fuel metering system, and is cost competitive when compared to a complete EFI system. An EFI system requires several peripheral components in addition to the injector(s), in order to duplicate all the functions of a carburetor. A point worth noting during times of fuel metering repair is that early EFI systems are prone to diagnostic ambiguity. A single carburetor replacement can accomplish what might require numerous repair attempts to identify which one of the several EFI system components is malfunctioning. Newer EFI systems since the advent of OBD II diagnostic systems, can be very easy to diagnose due to the increased ability to monitor the real-time data streams from the individual sensors. This gives the diagnosing technician real-time 13

feedback as to the cause of the drivability concern, and can dramatically shorten the number of diagnostic steps required to ascertain the cause of failure, something which isn't as simple to do with a carburetor. On the other hand, EFI systems require little regular maintenance; a carburetor typically requires seasonal and/or altitude adjustments.

Fundamentals of Fuel Injection MPFI system injects fuel into individual cylinders, based on commands from the ‘on board Engine management system computer’ – popularly known as the Engine Control Unit/ECU. MPFI Systems can either be: a) ‘Sequential’ i.e. direct injection into individual cylinders against their suction strokes, or b) ‘Simultaneous’ i.e. together for all the four or whatever the number of cylinders, or c) ‘Group’ i.e. into Cylinder-Pairs. 14

These techniques result not only in better ‘power balance’ amongst the cylinders but also in higher output from each one of them, along with faster throttle response. Of these variants of MPFI, 'Sequential' is the best from the above considerations of power balance/output. ‘Sefi’’, as advertised by Ford Ikon, stands for 'Sequential Electronic Fuel Injection', which technically is the best of the above variants of MPFI. Hyundai/Maruti MPFI systems are in fact Sefi too. Daewoo India had the (b) or (c) variants of above MPFI systems on its Cielo/Matiz. On the other hand, older Opel-Astra’s had a 'single point' fuel injection system, which is in between an MPFI and the now obsolete SingleCarburetors systems. The ‘Fuel Injectors’ are precision built ‘Solenoid Valves’, something like Washing Machine Water inlet Valves. These have either single or multiple ‘Orifices’ which ‘spray’ fuel into the Fuel inlet manifold of a Cylinder upon actuation, from a common Rail/Header pressurized to around 3 bar, fed by a high pressure electrically drive fuel pump inside the Petrol tank of the Car. The ‘on-board’ ECU primarily controls the Ignition Timing and quantity of fuel to be injected. The latter is achieved by means of controlling the ‘duration’ for which the Injector solenoid valve coil is kept energized – popularly known as the ‘pulse-width’.

15

MULTI POINT FUEL INJECTION SYSTEM In general, an ECU in turn is controlled by the ‘data input’ from a set of ‘SENSORS’ located all over the Engine and its Auxiliaries. These detect the various ‘operating states’ of the Engine and the performance desired out of it. Such Sensors constantly monitor : 1) Ambient Temperature, 2) Engine Coolant Temp., 3) Exhaust/manifold temp., 4) Exhaust ‘O2’ content, 5) Inlet manifold vacuum, 6) Throttle position, 7) Engine rpm, 8) Vehicle road speed, 9) Crankshaft position, 10) Camshaft position, etc. Based on a ‘programmed’ interpretation of all this input data, the ECU gives the various ‘commands’ to the Engine’s fuel intake and spark ignition timing systems, to deliver an overall satisfactory performance of the Engine from start to shut down, including ‘emission control’. To get the best out of an MPFI System, one should use – a) The OE recommended Petrol Additives or the new generation ‘Premium’ Petrol’s REGULARLY and b) NEVER Tamper with the OE Wiring Harness of the

16

Car – EVEN to install the ubiquitous Music System OR any other Electrical Accessory - other than those ‘approved’ OE/Dealer and designed to suit the Car’s Wiring Harness/CWH ‘Couplers’.

Various Injection Schemes MPFI systems function under two basic arrangements, namely Port injection Throttle body injection

Port Injection In the port injection arrangement, the injector is placed on the side of the intake manifold near the intake port . The injector sprays gasoline

17

into the air, inside the intake manifold. The gasoline mixes with the air in a reasonably uniform manner. This mixture of gasoline and air then passes through the intake valve and enters into the cylinder.

Every cylinder is provided with an injector in its intake manifold. If there are six cylinders, there will be six injectors.

Throttle Body Injection System Figure below shows the simplified sketch of throttle body injection system (single point injection). This throttle is similar to the carburetor throttle body, with the throttle valve controlling the amount of air entering the intake manifold.

18

An injector is placed slightly above the throat of the throttle body. The injector sprays gasoline into the air in the intake manifold where the gasoline mixes the air. This mixture the passes through the throttle valve and enters into the intake manifold. Fuel injection systems can be either timed or continuous. In the timed injection system, gasoline is sprayed from the injector in pulses. In the continuous injection system, gasoline is sprayed continuously from the injectors. The port injection system and the throttle body injection system may be either pulsed or continuous systems. In both systems, the amount of gasoline injected depends upon the engine speed and power demands. In some literatures MPFI systems are classified into two types: D-MPFI and L-MPFI.

D-MPFI System The D-MPFI system is the manifold fuel injection system. In this type, the vacuum in the intake manifold is first sensed. In addition, it senses the volume of air by its density.

19

As air enters into the intake manifold, the manifold pressure sensor detects the intake manifold vacuum and sends the information to the ECU. The speed sensor also sends information about the rpm of the engine to the ECU. The ECU in turn sends commands to the injector to regulate the amount of gasoline supply for injection. When the injector sprays fuel in the intake manifold the gasoline mixes with the air and the mixture enters the cylinder.

L-MPFI System The L-MPFI system is a port fuel injection system. In this type the fuel metering is regulated by the engine speed and the amount of air that actually enters the engine. This is called air mass metering or airflow metering.

20

As air enters into the intake manifold, the air flow sensor measures the amount of air and sends information to the ECU. Similarly the speed sensor sends the information about the speed of the engine of the ECU. The ECU processes the information received and sends appropriate commands to the injector, in order to regulate the amount of gasoline supply for injection. When injection takes place, the gasoline mixes with the air and the mixture enters the cylinder.

21

Conclusion Improved Fuel Consumption Vehicles with dual point fuel injection or carburetors do not get nearly the fuel economy of those with multi-point fuel injection. The underlying reason is that fuel delivery systems of these older vehicles are less precise. A multipoint fuel injection system, which uses one fuel injector for each cylinder of the engine, delivers just the right amount of gas to each cylinder. Thus, gas is not wasted in the process. Over time, the gas saved with a multi-point fuel injection system saves the vehicle owner loads of money.

Emissions Emissions test results are an important factor today. A car from this century emits a small fraction of what a vehicle emitted even a few decades ago. Multi-point injection systems are better for the environment because the emissions of hazardous chemicals being released when fossil fuels are burned are minimized. As mentioned above, the more precise delivery of fuel to the engine means that fewer noxious byproducts are released when the fuel combusts within the engine. The implements within the engine meant to clean the exhaust have been fine-tuned in a multi-point system to work more efficiently. Therefore, the engine--and the air--is cleaner as a result of multi-point systems.

Better Performance The performance of an engine suffers with the use of a carburetor, but multipoint fuel injection allows for far better engine performance. This is due to a few factors. Instead of allowing for additional air intake, multi-point injection atomizes the air that is taken through a small tube. Because multipoint injectors are usually controlled by computers, each function of a carburetor is performed by a different system component. These systems also improve the cylinder-to-cylinder distribution of an engine, which allows it to conserve energy.

22

References • • • • •

www.carblogindia.com www.indiacar.com www.wikipedia.org www.crazyengineers.com www.ehow.com • www.google.com (for images) • Internal Combustion Engines(III edition) by V Ganeshan

23

View more...

Comments

Copyright © 2017 KUPDF Inc.
SUPPORT KUPDF