Mercedes Tools Catalog

September 9, 2017 | Author: Crescentrising | Category: Diesel Engine, Fuel Injection, Electrical Connector, Screw, Machines
Share Embed Donate


Short Description

Download Mercedes Tools Catalog...

Description

MERCEDES BENZ TOOL CATALOG 2008

Table of Contents Section 01 General Engine Section 03 Cylinder Crankcase Section 05 Cylinder Head, Engine Timing Section 07 Injection Systems Section 13 V-Belts Section 15 Ignition Section 18 Engine Lubrication Section 20 Engine Cooling Section 25 Clutch & Pedal Linkage Section 26 Manual Transmission Section 27 Automatic Transmission Section 32 Suspension Section 33 Front Axle Section 35 Rear Axle Section 40 Wheels and Tires Section 41 Drive Shaft Section 42 Brakes - Mechanical Section 46 Steering Section 47 Fuel Supply Section 54 Instrument Cluster Section 82 Electrical Equipment Section 83 Heating & Air Conditioning Section B Body - General Section D Diagnostics Section K KABLEX

Baum Tools Unlimited Inc. © October 18, 2007

Page 4 7 9 14 21 22 23 25 27 28 30 34 36 38 40 41 42 44 46 47 49 51 52 53 55

Want a real Diagnostic Solution For German and Swedish cars? One that communicates with the vehicle and gives accurate fault information and live data to help solve problems fast. NOW YOU CAN OWN THE HIGH END “ iSCAN/cs2000” SCAN TOOL for a fraction of it’s original cost with the new European or Asian STARTER PACKS. PLUS get 30 days of FREE diagnostic tech support to get you started. ALL EURO Buy or lease for as low as $2,995

The most advanced European/ Asian scan tool on the market is now available with a NEW ALL EUROPEAN and/or ALL ASIAN lite STARTER PACK. Then you can upgrade to OEM level as your needs demand. Customize it because you don’t need coverage for vehicles already covered by your domestic scanner Systems covered include: * Drivetrain (Engine/Transmission...) * Chassis (Traction, Braking, Suspension...) * Body (Doors, Windows, Seats, Wipers...) * Information & Communications * Climate Controls (Heating, AC...) … and More Access to the following information (mfg. dependent): ◊ Live Data Stream ◊ Fault Code Handling ◊ Control Unit ID & Coding Info ◊ Component Activation ◊ Reset Adaptation ◊ Graphs Live Data ◊ Service Interval Resetting

iSCAN FREE 30 day Diagnostic Tech Support to get you on the Includes ► Procedures ► Troubleshooting ► Wiring diagrams ► Parts Location ► Known system failures

Road to European Diagnostic Success. ► Advanced tech support subscriptions specifically for iScan users ► Pay as you go advanced tech support specifically for German and Swedish car repair. We’ve got the knowledge and data to help. ► Training seminars in your area on diagnostic techniques and procedures.

European- Mercedes * BMW/Mini * Volkswagen/Audi/Seat/Skoda * Porsche * Volvo Asian- Toyota/Lexus * Nissan/Infinity * Honda/Acura * Mitsubishi * Mazda * Daewoo * Daihatsu * Suzuki 1991-2005 Hyundai * Kia * Subaru Domestic and foreign OBD-II & EOBD-III

“Hardware Repair” and “Refurb Exchange” program. You bust - we fix or exchange for refurb FAST.

NEW the Baum Tools credit card

New CAN Diagnostics (Slow & Fast) New Programmable Modules New Internet Software Updates New PC Link Software New Bluetooth Adapter for remote PC diagnostics. Dealer level info with CORRECT code definitions for OBD1(late 80’s to 1995) and OBD2 systems 1996 to present.

Apply now and pay for your scanner with your Baum Tool Credit Card and receive an extra 5% discount. Or use our 24 month NO INTEREST lease plan on full packages. It’s like FREE money.

Call for complete systems, features and coverage list for the cars you work on.

Attn: Current owners of iSCAN/CS2000 and VScan Update your gear for as much as 30% off. Some packages include FREE hardware upgrades HARDWARE UPDATES • • • • •

Exchange your CS2000 or Vscan unit for a new iScan with a bigger bettery quality screen, faster processor, contrast control, etc. Get a Second CS2000 or Vscan base unit Upgrade to a new iScan base unit for a price never available before. Exchange some of your old cables for new high speed multiplexing cables that do the job of two or three old cables Add the new Bluetooth PC communications adapter and start remote diagnostics from up to 100 feet.

SOFTWARE UPDATES • Update earlier versions to the latest new vehicle coverage with more features and systems. • Get up to 2005, 2006 and some 2007 coverage with all European or Asian models with the new STARTER PACK • Add Programming, coding, adaptation and more with the full iScan software. Call us and talk to our techs that can help get you the proper fit for the vehicles you work on.

One Size Does Not Fit All

800-848-6657

BAUM TOOLS UNLIMITED INC. 941-927-1414 Intnl” 941-927-1612 Fax PO Box 5867 Sarasota FL 34277-5867 http://www.baumtools.com / [email protected]

Section 01 General Engine

Mercedes Tool Tool Number 117-0223

Application CASE DRILLING FIXTURE - V8

General Engine

01

Models M116, 117

Use to install Timesert inserts when the cylinder bolt holes strip in the light alloy type engine case. Use with Timesert kit #TS1015 and inserts #TS10155.

TS1015

TIMESERT KIT-10X1.5mm

M116, M117

Timesert kit for rethreading case when cylinder head bolts strip out. Use with alignment jig #117-0223 and inserts #TS10155.

TS10155

TIMESERT INSERTS 10X1.5X24.5mm

M116, 117

Bulk Timesert inserts for case repair on Mercedes Benz V8 and BMW and VW air cooled engines.

602-0033

IMPACT EXTRACTOR FOR PRE CHAMBERS - DIESEL Slide hammer with #902-0033B threaded adapter for removing the pre combustion chambers on diesel models.

902-0033B

PRE CHAMBER PULLER SLIDE HAMMER ADAPTER - DIESEL Special slide hammer adapter for removing pre combustion chamber from early and late model Turbo Mercedes diesel models. Use with #6020033B. Has both coarse and fine threads.

615-0007

PRE-CHAMBER RETAINER RING PIN WRENCH - DIESEL

OM601, 602, 603, 604, 605, 606, 615, 616, 617

DIESEL

OM604, 605, 606, 615, 616, 617

DIESEL

OM615, 616, 617

DIESEL

OM602, 603, 604, 605, 606, 617.95

DIESEL

OM604, 605, 606, 648

DIESEL

OM601, 602, 603, 617 Turbo

DIESEL

OM615, 616, 617.91/93

DIESEL

Use to remove and install the threaded retainer ring of the pre-chamber.

ST3000

PRE CHAMBER RETAINER RING SOCKET - DIESEL Multi spline socket for removing pre combustion chamber retainer ring on late model indirect injection diesel models. MB #604 589 0109 which replaced #603-589-0009.

B606-0053

GLOW PLUG BORE REAMER - 'PENCIL' TYPE EXTRA LONG Special 12x1.25mm extra long threaded reamer for removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. For models from 1996 to end of production.

901-0053

GLOW PLUG BORE REAMER - 'PENCIL' TYPE - DIESEL Special 12x1.25mm reamer for removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. For models from 1983 to end of 603 production.

917-0053

GLOW PLUG REAMER - LARGE TYPE - DIESEL Special 18x1.25mm threaded reamer for removing heavy carbon deposit from glow plug hole which is a major cause of glow plug failure. For models from 1967 to 1985. Non Turbo. Universal not included.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 4

www.baumtools.com [email protected]

Mercedes Tool Tool Number 916-0013

Application HEX HEAD SOCKET - 8mm 'C' 1/2" DRIVE

General Engine

01

Models M116, 117

Use to access head bolts under rocker shaft for R&R and torquing. (See #ST3054-G8 and #ST3149-8)

ST3054/8G

HEX HEAD SOCKET - 8mm DOGLEG 1/2" DRIVE

M116, 117

Special bend for access to head bolts next to exhaust manifold on V8. (See #ST3149-8 and #916-0013 below)

ST3149-8

UNIVERSAL HEX HEAD SOCKET - 8mm 3/8" DRIVE.

M116, 117

Use to remove cylinder head bolts at rear of case. Use with sockets #ST3054-8G and #916-0013.

ST1054TXT55

HEADBOLT SOCKET - TORX T55 Special 130mm long T55 TORX headbolt socket for 112 engine. Use with #H992LG-T55 to remove all bolts. Mercedes #000-589-0310

H992LG-T55 HEADBOLT SOCKET - T55 TORX 90mm 1/2"DR. Special round shaft 96mm long socket for the T55 TORX socket head bolt on cylinder head of late model 6 and 8 cylinder engines.

ST3004

CYLINDER HEAD SOCKET 12mm XZN X 55mm 1/2"DR. XZN Hex Head Socket-12mm x 55mm 1/2" drive with special short format for cylinder head bolts. See #ST3004.

ST3054XM12

CYLINDER HEADBOLT SOCKET - 12mm

ST3054XM10

XZN HEX HEAD SOCKET - 10mm X 140mm 1/2" DRIVE

Use to remove and install cylinder head bolts. Tri-square socket head screws (XZN). 12mm 12 point 1/2 square socket, 140 mm long for screws on cylinder head.

Special round shank for head bolts and driveshaft bolts.

ST3054X-M8 XZN HEX HEAD SOCKET - 8mm X 140mm 1/2" DRIVE

M112, 113, 155, 275, 612

M112, 113, 155, 275

104, 112, 113, 119, 120

M102, 103, 104, 110, 116, 117, 119, 120, 615, 616, 617

M112, 113, 137, 127, OM602, 603, 604, 605, 606, 612, 613, 628, 629, 647, 648

M115, 116, 117

Use to remove and install a variety of head and accessory bolts, particularly on V8 models.

ST1054/5

HEX HEAD SOCKET - 5mm x 180mm 1/2" DRIVE

All

5mm x 180mm long body for various engine bolts.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 5

Mercedes Tool Tool Number ST3054/8L

General Engine

Application

01

Models

HEX HEAD SOCKET - 8mm X 130mm 3/8" DRIVE

M115, 116, 117

130 mm long, 1/2" square drive, for Allen screws on cylinder head.

ST1054/10

103-0114

HEAD BOLT HEX HEAD SOCKET - 10mm X 160mm Use this long Allen head socket to remove and install cylinder head bolts.

M100, 110, 114, 115, 130, 180, OM615, 616, 617

CAMSHAFT SEAL GUIDE SLEEVE - 20 mm

M103, 104, 120

Use to install the camshaft sealing ring with cover on. Protects seal lip from damage.

119-0014

CAMSHAFT SEAL GUIDE SLEEVE

M119

Use to mount shaft sealing ring with cover on camshaft.

Camshaft Aligment Kit M112 & M113

B112-0001K Use this kit to properly align camshafts during assembly of 6 and 8 cylinder M112 and M113 engines. Kit includes intake and exhaust gauges and cam turning wrench.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 6

www.baumtools.com [email protected]

Section 03 Cylinder Crankcase

Mercedes Tool Tool Number 285-0240

Application FLYWHEEL LOCK

Cylinder Crankcase

03

Models

NEW

M275, M285

Retaining lock for crankshaft on starter ring gear.

112-0040

VIBRATION DAMPER COUNTER-HOLDER

M112, M113, M137

Holds vibration damper when loosening and tightening center bolt. Handle can be extended with commercially available pipe, e.g. 3/4 din 2441, diameter 26.9 x 3.25 mm, length 1000 mm M112, M113, M137

1106

CYLINDER LEAKDOWN PRESSURE TESTER

All

Check cylinder leakage rate to detect worn or broken rings, gaskets, cylinders and valves. Kit includes: Heavy duty gauges, hose, 10mm and 14mm spark plug port adapters.

111-1231

112-0340

DIPSTICK TUBE DRIVER Installing tool for dipstick allows easy installation in most models.

M102, 103, 104, 111, 116, 117, 119, 601, 602, 603, 615, 616, 617

FLYWHEEL LOCK

M112, 113, 137

Use to lock crankshaft on starter ring gear (mount in starter hole) for vehicles with left and right-hand steering.

601-0240

FLYWHEEL LOCK Locks flywheel at starter ring gear from the transmission side.

602-0040

FLYWHEEL LOCK Locks flywheel from the starter side.

116-0140

FLYWHEEL LOCK Locks crankshaft on starter ring gear.

110-0040

FLYWHEEL LOCK Use to lock flywheel at starter ring gear.

119-0114

FRONT CRANKSHAFT SEAL RING SLEEVE For pressing in the front crankshaft radial seal ring

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M102, 103, 104, 111, 601, 602, 603, 604, 605, 606, 611, 612, 613

M102, 103, 104, 111, 120, 137, 601, 602, 603, 604, 605, 606

M110, 115, 116, 117, 119, 615, 616, 617

M110, 615, 616, 617

M112, 113, 119, 120

www.baumtools.com [email protected] 7

Mercedes Tool Tool Number 110-0761

Application CRANKSHAFT SEALING RING SLEEVE INSTALLER Use to press in the front crankshaft radial seal ring for pulley end of crankshaft.

111-0843

REAR CRANKSHAFT RADIAL SEAL INSTALLER Tool for pressing rear crankshaft radial seal into position on crankshaft. Additional sleeve with 3 mm offset to the inside for later models.

ST3676

OIL DRAIN WRENCH - 14mm HEX X 13mm BOX Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)

ST3677

OIL DRAIN WRENCH - 14mm HEX X 17mm BOX Use to service oil, differential and transmission drain plugs.

KO4012M-14 OIL DRAIN HEX HEAD SOCKET 14mm 1/2" DRIVE

Cylinder Crankcase

03

Models M110, 116, 117, 123

M102, 111, 112, 113, 137, 275, 601, 602, 603, 604, 605, 606, 628

W107, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220

M110, 107, 116, 117, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220, 615, 616, 617, 716, 717 All

Short body allows easy removal of oil, differential and transmission drain plugs.

H2740

SWIVEL HEX HEAD SOCKET - 6mm 3/8" DR. LONG EXTENSION.

All

Removes and installs water pump hex head bolts.

ST51-27

DRIVE SHAFT SOCKET - 27mm

All

12 point 1/2" DR. socket for loosening and tightening the center bolt of the crankshaft. All models except 100.

KK22-1

INTERNAL EXTRACTOR COUNTER STAY - SMALL

DIESEL

All

Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)

KO4012M

SHORT HEX HEAD SOCKET - 1/2 "DRIVE

All

Short hex head sockets for access to tight locations. Sizes available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm. 12, 17 and 19mm most common for Mercedes.

W1088

PILOT BEARING PULLER - 10mm - 25mm

All

Universal pilot bearing and bushing puller. Particularly narrow format and sharp lip allows access to even the hardest to get at bushings and bearings without damage.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 8

www.baumtools.com [email protected]

Section 05 Cylinder Head, Engine Timing

Mercedes Tool Tool Number 137-0140

Cylinder Head, Engine Timing

Application RETAINERS; CAMSHAFT (2 pcs)

05

Models M137, M275

NEW

M271

NEW

M271

NEW

M275, M285

NEW

M275, M285

NEW

Used to hold camshafts in position 30 degrees ATDC; for loosening and tightening the bolt that attaches the camshaft sprocket or to adjust cam timing (2 pieces).

271-0061

CAMSHAFT RETAINER Retaining device makes it possible to position the camshafts in the installed position. This makes it possible to slacken and tighten the bolts attaching the camshaft gear.

271-0140

TIMING CHAIN RETAINER Retainer for drawing in the timing chain. Retains timing chain with camshaft sprockets in proper timing position.

285-0040

RETAINER, CAMSHAFT (LEFT) Used to hold LEFT bank camshaft position at 300 after TDC to accommodate cam gear removal and cam timing adjustment. NOTE: For RIGHT bank camshaft, use 137 589 01 40 00.

285-0140

TIMING CHAIN RETAINER Used to retaining timing chain on sprocket during chain replacement operation.

000-5843

CHAIN LINK PRESS - DOUBLE ROW

All

Use to press on external lugs and rivets of dip-type fasteners of duplex roller chain. Use with #103-0163 to rivet single row chains. See #9665843 to remove rivets.

103-0163

CHAIN LINK PRESS ADAPTER - SINGLE ROW Use with tool #000-5843 to rivet single row timing chains.

112-0963

966-5843

CHAIN LINK PRESS ADAPTER - DOUBLE ROW

M102, 103, 104, 111, 112, 113, 116, 166, 602, 603, 611, 612, 613, 640, 646, 647, 648, 668

Includes: chain guide and press thrust pieces. Use for pressing rivet onto outer link. Use with rivet pressing tool #000-5843. This set comes with #000-5843.

M102, 104, 110, 111, 112, 113, 116, 117, 119, 120, 116, 275, 611, 612, 613, 642, 646, 647, 647, 668

TIMING CHAIN SPLITTER - SINGLE & DOUBLE ROW

All Engines

Use to separate single and double row timing chains without damaging links.

915-0734

CHAIN RAIL PIN PULLER - HEAVY DUTY

All

Pulls sliding rail pins on all models. Includes: Puller and 5mm, 6mm, and 8mm spindles.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 9

Mercedes Tool Tool Number B116-0134

Cylinder Head, Engine Timing

Application THREADED ROD - 6 x 8 X 50mm Use with chain rail pin puller #915-0734. (1 piece)

116-2033

CHAIN RAIL PIN PULLER - SLIDE HAMMER TYPE Removes tensioner rails and rocker pins. Includes: Slide hammer and 5mm, 6mm, 8mm and 10mm threaded pins.

116-2033P

CHAIN RAIL PIN PULLER - THREADED ROD SET

05

Models M110, 115, 116, 117, 119, 155, 272, 275, OM601, 602, 603, 604, 605, 606, 612, 615, 616, 617, 628, 640, 642 M102, 103, 104, 110, 111, 116, 117, 119, 120, 272, 275, OM601, 602, 603, 606, 612, 615, 616, 617, 628, 640, 642 All

Replacement threaded rods for #116-2033 chain rail pin puller. Sizes #1160034 - 5x150mm, #116-0134 6x50mm, #116-0234 6x150mm, #616-0034 8x150mm and #116-0334 10x100mm spindles.

900-0307

A/C IDLER PULLEY ALLEN WRENCH - 8mm x 10mm Special A/C idler pulley wrench allows access to 8mm bolts on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 V8 models. Also see kit #B9042.

B112-0001K CAM ALIGNMENT KIT

M102, 103, 116, 117

NEW

112, 113,

This kit contains the intake and exhaust cam alignment jigs and the cam holding wrench.

112-0032

CAMSHAFT HOLDING PLATE

M112, 113

Holds camshaft in 40 degree TDC position. Right side.

112-0132

CAMSHAFT HOLDING PLATE

M112, 113

Holds camshaft in 40 degree TDC position. Left side.

111-0315

RETAINING PINS (2 pairs) each connected with flexible tubing, for holding camshaft in installation position (25 after ignition TDC)

112-0001

OPEN END WRENCH - 38mm

M111, 119, 604, 605, 606, 611

M112, 113

Special wrench to turn and hold camshaft when installing sprocket gear.

119-0001

CAMSHAFT TURNING WRENCH

M104, 119

Double open end wrench 26.5mm X 27.5mm 256mm long for turning camshaft to assembly position.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 10

www.baumtools.com [email protected]

Mercedes Tool Tool Number 116-0101

Cylinder Head, Engine Timing

Application CAMSHAFT HOLDING WRENCH Aluminum wrench for holding and turning camshaft during assembly and timing.

917-0623

HYDRAULIC LIFTER GAUGE V-8 Measures valve clearance so proper compensating element disk can be installed.

102-0421

HYDRAULIC LIFTER GAUGE - 4 AND 6 CYLINDER

05

Models M110, 115, 116, 117, OM615, 616, 617

M116, M117 from 1978

102, 103

Measures valve clearance so proper compensating element disk can be installed.

112-0440

CHAIN LOADING FIXTURE

NEW

M112, 113

Use to load timing chain onto sprocket on 6 and 8 cylinder engines.

M0037

TIMING CHAIN LOADER V-8

M115, 116, 117

Holds chain tight against cam sprocket so chain can't slip during installation. Cuts time and manpower in half. Early V8 models.

M0037-104 CHAIN LOADER - M104

M104

Holds chain tight against cam sprocket so chain can't slip during installation. Cuts time and manpower in half.

M0037-119 CHAIN LOADER - 119

M119

Holds chain tight against cam sprocket so chain can't slip during installation. Cuts time and manpower in half.

ST3545-17

VALVE ADJUSTER - 17mm CROWFOOT 1/2" DRIVE V8 Special cut out bottom on this wrench allows easy adjustment of valves on V-8 models. (2 piece wrench) (#916-0201)

ST3545-14

VALVE ADJUSTER - 14mm CROWFOOT 1/2" DRIVE

M115, 116, 117 (except hydraulic lifter types)

M180

Use to adjust valves on early 6 cylinder models. (2 piece wrench) (#9110101)

615-0001

VALVE ADJUSTING WRENCH SET - 14mm PAIR Diesel valve adjusting wrenches. Use with retaining nut holder #615-0003.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

OM615, 616, 617

DIESEL

www.baumtools.com [email protected] 11

Mercedes Tool Tool Number 615-0003

Cylinder Head, Engine Timing

Application DIESEL SPRING PLATE HOLDING WRENCH - 30mm

05

Models OM615, 616, 617

Use to hold retaining nut when adjusting valves with wrench pair #6150001.

71B

COMPRESSION GAUGE - 300psi GASOLINE

DIESEL

All, except Diesel

Features flexible hose, side release valve and 10mm and 14mm screw in adapters for spark plug holes.

M70TE

DIESEL COMPRESSION GAUGE - 1000 psi Direct reading compression gauge with hose and quick connect adapter for diesel engines. Please request adapter when ordering.

M70TE/1

DIESEL COMPRESSION GAUGE ADAPTER - EARLY MODEL NOZZL

OM601, 602, 603, 604, 605, 606, 615, 616, 617

DIESEL

OM615, 616, 617

DIESEL

OM601, 602, 603, 606

DIESEL

OM615, 616, 617

DIESEL

OM601, 602, 603, 604, 605, 606, 612, 617 Turbo

DIESEL

OM604, 605, 606, 612

DIESEL

Adapter for early large injection nozzle port. 24mm X 2.0mm

M70TE/1A

DIESEL COMPRESSION GAUGE ADAPTER - LATE MODEL NOZZLE Adapter for later model diesels with small injection nozzle port. 22mm X 1.5mm

M70TE/2

BOSCH GLOW PLUG 18X1.5mm - EARLY MERCEDES Adapter for early large Glow plug port. 18mm X 1.5mm

M70TE/2A

BOSCH GLOW PLUG 12X1.5mm - LATE MODELS Adapter for later model diesels with small Glow plug port. 12mm X 1.5mm

M70TE/X

DIESEL COMPRESSION ADAPTER EXTENSION Use to access deep port injectors or glow plugs on late model engines. Use with adapter #M70TE/2A.

M1160

VALVE SPRING COMPRESSOR KIT - 102, 103, 601 ENGINES Use to depress valve springs for replacement of seals, stems, or valves on late model 4 and 6 cylinder engines. Includes: #601-0261, #102-0161, #103-0061

111-1861

VALVE SPRING COMPRESSOR ARM Use with tool #102-0161 for 102. Use with tool #102-0359 for 102-16 valve. Use with tool #103-0061 for 103 Use with tool #601-0259 for 601. Use with #111-0059 for all others.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 12

M102, 103 (except 4-valve )

M102, 103, 104, 111, 112, 113, 119, 120, OM601, 602, 603, 604, 605, 606

www.baumtools.com [email protected]

Mercedes Tool Tool Number 103-1161

Cylinder Head, Engine Timing

Application VALVE SPRING COMPRESSOR FOOT - M102/M103

05

Models M102, 103

Use with valve compression lever #111-1861 and #102-0359 to compress valve springs on M102 and M103 engines.

102-1063

VALVE SPRING COMPRESSOR FOOT - 28mm (4 VALVE)

M102

Use with valve compression lever #111-1861 and #102-0359 to compress valve springs on 102 2.3L 16 valve engines.

272-0061

VALVE SPRING COMPRESSOR FOOT

M272, 273

Use with #111-2561 to compress valve springs to allow R&R of spring retainer.

123-0361

VALVE SPRING COMPRESSOR - 6 CYL. & V-8 Use to depress valve springs for replacement of seals, stems, or valves on pre 1991 6 cylinder (except 110) and 8 cylinder engines through 1991. For 110 engine see #110-0461. All parts are available separately.

116-0663

VALVE KEEPER REMOVER

M114, 115, 116, 117, 130, 180

All

Special magnetic finger to remove conical valve keepers.

104-0037

VALVE STEM SEAL PLIERS

All

Special tips and 25 degree bend allow easy pulling of valve stem seals.

ST11063

VALVE STEM SEAL PLIERS

All

Use to remove valve stem seals.

H2740

SWIVEL HEX HEAD SOCKET - 6mm 3/8" DR. LONG EXTENSION.

All

Removes and installs various hex head bolts from cylinder head.

W7080

VALVE STEM SEAL INSTALLER Installs 7mm and 8mm valve stem seals. (#119-0043)

116-0043

VALVE STEM SEAL INSTALLER - 9mm Use to press in the 9mm valve stem seal onto the valve guide sleeve.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M104, 111, 112, 113, 119, 120, 604, 605, 606, 668

M110, 115, 116, 117

www.baumtools.com [email protected] 13

Section 07 Injection Systems

Mercedes Tool Tool Number

Application

Injection Systems

07

Models

STAR DIAGNOSTIC SYSTEM - COMPACT 3 SDSCOMPACT3 Mercedes factory diagnostic system. Includes DAS and WIS systems.

All from 1988

NEW

SDS-BASIC2 STAR BASIC 2 DIAGNOSTIC SYSTEM

All from 1988

NEW

Mercedes Star Basic 2 factory diagnostic system includes DAS. WIS sold separately.

CS2-CMP38 MERCEDES 38 PIN MULTIPLEXER

From 1992-2000

Use with the CS2000 scanner to automatically switch from one system to another, when performing diagnostics. Can only be used with version 3.6F or PV1.21F or later software. Use with B140-1463A for longer extension.

140-1463

MUSHROOM 38 PIN BREAK-OUT ADAPTER Allows easy access to the 38-pin diagnostic socket when using scanners CS2000, CS1000 or with a standard DMM.

B140-1463A 38 PIN X 38 PIN 7' EXT CABLE Extension cable allows use of test equipment while driving or on dynamometer.

iScanMercedes

DBL800

MERCEDES BENZ DATA SCANNER

W129, 140, 170, 202, 203, 208, 210, 220

W124, 129, 140, 202, 208, 210

All from 1988

Use to read and reset fault codes, access live data for road tests, activate components and program/code controllers. See inside cover for more details.

DEUTRONIC POWER SUPPLY/BATTERY CHARGER

All Models.

NEW

All

NEW

All Models from 1996 to the present.

NEW

All models 19942006

NEW

Microprocessor controlled charger/power supply to maintain power levels during programming and diagnostics. Microprocessor controlled charging, measuring and monitoring. Built-in interface for computer, programming unit, printer and large display.

B7205J

TERMINATOR The Terminator is a superior Logic probe combining the features of a DMM and oscilloscope but simplifying the display for technicians that want to find the pulse but don’t need the to see the trace. Particularly useful for tracing CAN signals.

OBD2-BOB

OBD-II BREAK OUT BOX This J1962 break out box allows access to all wires in the OBD-II / EOBD III Diagnostic Interface This makes it easy to trace CAN Bus faults, Power supply problems and track failed diagnostic controllers.

OBD2-300

OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes. Comes with instruction manual with over 2000 fault code definitions.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 14

HOT

www.baumtools.com [email protected]

Mercedes Tool Tool Number OBD2-500

Application OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes live data, freeze frame, ands all SAE OBD-II modes 1 thru 9. SAE1850, ISO and CAN protoccols. Comes with instruction manual with over 2000 mfg. fault code definitions.

909-0021

LAMDA CONTROL LOOP TESTER - 100/100IR

Injection Systems

07

Models All models 19942008

NEW

All

Ratio meter for checking on/off ratio and setting CO levels. Includes late models 100/100IR setting. Connects directly to round 8-pin diagnostic plug. Models 1980-93.

M99

LAMBDA CONTROL TESTER Open/closed loop tester allows analysis on lambda feedback loop. Use to set CO level, check O2 sensor and ECU for proper rich/lean response. Self detects proper wires on 4 wire O2 sensors. Applicable too all models. See #909-0021.

M501

THROTTLE POTENTIOMETER TESTER

All O2 Sensor Equipped

M111, M112, 113,

Test the throttle potentiometer used in all late model engines.

B1630

RESISTANCE SUBSTITUTION BOX

NEW

All

Resistance substitution box allows testing and calibration of dash gauges, injection system sensors, cruise control, and anti theft systems. (#1240963)

140-0133

MOUNTING LEVER

M104, 119, 120

For module from module box.

A0202

BREAK-OUT BOX - 120-PIN W/CASE

All

Basic 120 pin break out box to test the contacts, continuity, inputs and outputs of a variety of electronic control units. Adapters are available for Bosch, Siemens and TEVES 25, 35, 38, 55, 68 and 88 pin connectors as well as many others.

A0201

BREAK-OUT BOX - 60-PIN W/CASE

All

Basic 60 pin break out box to test the contacts, continuity, inputs and outputs of a variety of electronic control units. Adapters are available for Bosch, Siemens and TEVES 25, 35, 38, 42, 55 and 60 pin connectors as well as many others.

A020201

25-PIN BREAK OUT BOX CABLE KE1, KE2, KE3.1, KE3.5, L2, D-Jet, EZK, 4MATIC

A020202

35 PIN BREAK OUT BOX CABLE K-Jet, KE3.2, KE3.3, ABS2/2B, ABS (202), EGS

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

W107, 124, 126, 129, 140, 201

W107, 124, 126, 129, 140, 201, 202

www.baumtools.com [email protected] 15

Mercedes Tool Tool Number A020204

Application 55-PIN BOSCH BREAK OUT BOX CABLE KE5.1, KE5.2, ABS 3 & 5 and later, EGS, IFI Diesel, ASR (202).

A020235

88-PIN BOB ADAPTER HFM Injection. 44 x 44 pins.

102-0463

TEST HARNESS - EHA Tests CIS-E electronic idle speed control with standard multimeter. (VOMDMM)

103-0063

TEST CABLE - 3 PIN Use to adapt # 909-0021 to later type idle control units.

ST10507

CO ADJUSMENT HEX SCREWDRIVER - 3mm X 380mm long Use to adjusts CO and idle mixture control screw on fuel injection distributor. MB #000-589-1411

ST12975

FUEL LINE CLAMP - 30mm

Injection Systems

07

Models W124, 129, 140, 202, 208, 210

W124, 129, 140, 202, 210

W102, 103, 112, 113, 116, 117

M102, 103, 104, 116, 117

M102, 103, 110, 116, 117

All

Use to block off fuel line when working on fuel system or removing engine.

B611-0421

COMMON RAIL INJECTOR BACK FLOW TESTER

Common Rail Diesel

Use to measure fuel return rate from injectors in common rail diesels. Includes adapters and 6 graduate cylinders and 6 graduated bottle.

1318-R

FUEL INJECTION PRESSURE GAUGE - ECONOMY KIT

NEW DIESEL

Injected Engines

Checks charging (supply), running and leakage pressures of all types of injection systems. Includes: Gauge (160psi/1100kpa), 3-way switch, hoses and fittings and storage case.

1318-M

FUEL INJECTION PRESSURE TEST - MASTER KIT

All Models

Checks charging (supply), running and leakage pressures of all types of injection systems. Includes: Gauge (160psi/1100kpa), 3-way switch, all hoses, all fittings and storage case.

1318/1

GAUGE 0-1100KPA/0-160psi

Injected Engines

Dual range gauge with 1/4" NPT shank.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 16

www.baumtools.com [email protected]

Mercedes Tool Tool Number 1318/2

Application THREE WAY SWITCH

Injection Systems

07

Models Injected Engines

Special pressure switch allows easy switching from charge to run to leak pressure testing.

1318/4

MALE ADAPTER - 10X1mm X 12X1.5mm Male to Male adapter with dual conical fittings.

1318/5

FEMALE ADAPTERS

All

Female to Male adapters. Sizes available 8x1mm x 12x1.5mm, 10x1mm x 12x1.5mm, 12x1.5mm x 12x1.5mm, 14x1.5mm x 12x1.5mm. Please specify size when ordering.

1318/6

MALE ADAPTERS

All

Male to Male adapters. Sizes available 8x1mm X 10x1mm, 8x1mm X 12x1.5mm, 8x1mm X 12x1.5mm X 70mm, 12x1.5mm x 12x1.5mm, 14x1.5mm x 12x1.5mm. Please specify size when ordering.

1318/8

THREADED BANJO RINGS

All

Threaded banjo rings for testing in tight spots. Sizes available 8mm X 10x1.5mm Male, 10mm X 12x1.5mm. Specify size when ordering.

1318/10

COPPER WASHERS

All

8, 10 or 12mm Diameter

1318K

UNIVERSAL ADAPTER KIT

All Models

Contains all the adapters for tool # 1318.

1318/11

REPLACEMENT HOSE F/F FLARE - 10mm X 12mm

All

Heavy duty metal braided replacement hose for pressure gauges. 10x1.5mm X 12x1.5mm. Available in 300mm and 500mm lengths.

1318/12

REPLACEMENT HOSE F/F FLARE - 12mm X 12mm

All

Heavy duty metal braided replacement hose for pressure gauges. 12x1.5mm X 12x1.5mm. Available in 300mm and 500mm lengths.

119-0463

LH FUEL PRESSURE HOSE With 7/16-20 tapered SAE angled connection and 12 x 1.5mm union nut for LH fuel injection system (use with tester #103-0021).

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M104, 111, 112, 113, 119, 120

www.baumtools.com [email protected] 17

Mercedes Tool Tool Number 691STE

Application CARBURETOR SYNCHRONIZER (STE)

Injection Systems

07

Models All Carbureted

Plug type base with exchangeable tips for different types of carburetors.

691A

'UNI-SYN' CARBURETOR SYNCHRONIZER

M114, 130, 180

Round base synchronizer for use on most standard throat carburetors.

000-3323

SYNCHRONIZER HOOD

M114, 130, 180

Allows synchronizing of dual oval type carburetors with large circular formats found in some foreign model carburetors such as Weber, Zenith...etc. Use with either # 691A or 000-1223.

691H

GRADUATE CYLINDER - 1000ML.

All .

Use for fuel pump, injection pump, and injector output volume measurements. NALGENE material, non-breakable, resists gasoline and solvents for long life.

ST11085

FINE REAMERS 0.33 - 2.00mm

All Models

Tapered reamers allow precision reaming of carburetor main jets, injectors, solenoids and other small orifices. Set includes 13 reamers and pin vise.

M24D

DIESEL INJECTION NOZZLE TESTER

All Diesel Engines

DIESEL

All diesel models

NEW

Diesel from 1997 on.

NEW

OM601, 602, 603, 605, 606

DIESEL

OM601, 602, 603, 605, 606, 617.95

DIESEL

Test opening pressure, spray pattern, and cleans injectors. Kit includes: Gauge (7000psi/500bar) pump and steel adaptor line. May be upgraded to test gasoline injectors.

M500

GLOW PLUG ANALYZER Use to test 12 volt glow plug systems in late model diesel engines.

M502

DIESEL FUEL PRESSURE TESTER Measures the diesel fuel pressure in high pressure CDI type engines.

601-0514

INJECTION PUMP CENTERING SLEEVE - DIESEL Aligns injection pump for proper timing during removing and installing of injection pump.

617-0821

DIESEL TIMING TOOL - STATIC Position transmitter to measure start of fuel delivery using the RIV method.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 18

www.baumtools.com [email protected]

Mercedes Tool Tool Number 601-0521

Application INJECTION PUMP LOCK PIN - LATE MODEL Locks diesel pump cam to maintain timing during pump installation.

900-8673

INJECTION PUMP LOCK PIN - EARLY MODEL Locks diesel pump cam to maintain timing during pump installation.

936-0223

DIESEL DRIP TUBE Use to adjust start of fuel delivery.

916-0021

VACUUM CONTROL ADJUSTING ROLLER Use to measure vacuum pressures to vacuum control valve.

ST51-27

DIESEL NOZZLE SOCKET - 27mm Special 12 point 1/2" DR. socket with interior relief to accommodate the small leakage return tubes on top of injection nozzle. Also available in Hazet brand.

606-0009

INJECTION NOZZLE SOCKET - 22mm

Injection Systems

07

Models OM601, 602, 603, 605, 606, 617

DIESEL

OM615, 616, 617, 621

DIESEL

OM615, 616, 617 to 1983

DIESEL

OM616, 617.91, 617.95

DIESEL

OM601, 602, 603,612, 615, 616, 617, 646, 647, 648

DIESEL

OM604, 605, 606

DIESEL

OM601, 602, 603, 605, 606, 617

DIESEL

OM601, 615, 616, 617

DIESEL

OM611, 612, 613, 628, 640, 642, 646, 647, 648

DIESEL

OM601, 602, 603, 606

NEW

Use for removal and installation of diesel injection nozzle.

617-0109

SERRATED WRENCH SOCKET Use to remove and install the injection pump stub pipe and pressure valve on diesel pumps.

H4561

DIESEL PUMP MOUNT BOX WRENCH - 13mm Special 'L' wrench to access injection pump mount screws.

ST10627

GLOW PLUG CONNECTOR PLIER Use to remove and install the glow plug connectors on S class diesel models from 2000 onward.

ST3047-12

GLOW PLUG SOCKET - 12mm Special deep 12mm socket for removing and installing glow plugs in tight spaces.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 19

Mercedes Tool Tool Number ST4335-12

Injection Systems

Application GLOW PLUG SOCKET WRENCH Special 12mm socket wrench to remove "pencil" type glow plugs in the tightest places.

ST4335-21

07

Models

GLOW PLUG SOCKET WRENCH

OM601, 602, 603, 604, 605, 606, 617.95

DIESEL

OM615, 616, 617

DIESEL

OM615, 616, 617, 602, 642

DIESEL

OM601, 602, 603, 604, 605, 606, 611, 612, 613, 628, 640, 646, 647, 648, 661, 662, 668

NEW

OM601, 602, 603, 604, 605, 606

DIESEL

Special 21mm socket wrench to remove glow plugs in the tightest places.

H4550

INJECTION LINE CROWFOOT - 17mm 3/8"DR. Special wrench for injection lines.

ST440-14

CROWFOOT SOCKET - 14mm 1/4" DRIVE Use to access injection pipe cap nuts.

601-0008

INJECTION PUMP SPLINED WRENCH Use for rotating the injection pump camshaft.

M0035A

GAS TANK SOCKET - 46mm

All

Use to remove fuel tank filter body and fuel gauge sending units.

T13-22

HEX HEAD BIT - 22mm Use to remove gas tank drain plugs on late model cars. 22mm.

All from 1980 to present

#B611-0421 COMMON RAIL INJECTOR BACK FLOW TEST KIT Use to measure fuel return rate from injectors in common rail diesels. Includes adapters and 6 graduate cylinders and 6 graduated bottles. OM611.981 /987, 612.981, 647.981, 611, 612, 613, 628, 646, 647, 648

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 20

www.baumtools.com [email protected]

Section 13 V-Belts

Mercedes Tool Tool Number ST1009DC

V-Belts

Application

13

Models

PULLEY MOUNT BOLT WRENCH - 10mm

M116, 117, 119

Special 10mm Allen wrench 500mm long. Use to loosen and tighten the mount bolts of the idler pulley when adjusting v-belt of refrigerant compressor.

900-0307

A/C IDLER PULLEY ALLEN WRENCH - 8mm x 10mm Special A/C idler pulley wrench allows access to 8mm bolts on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 V8 models. Also see kit #B9042.

Mercedes/BMW Fan Service Kit

M102, 103, 116, 117

Kit Contains: 32mm - BMW Viscous Fan Nut BMW Pulley Holder #115150 36mm - Mercedes Viscous Fan Nut 65mm - Mercedes Fan Clutch Nut Mercedes Fan pulley holder #113-0040 Mercedes Water Pump holder #103-0040 Fan Belt Service/Idler Pulley Wrench 8mm and 10mm #900-0307

B9042

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 21

Section 15 Ignition

Mercedes Tool Tool Number ST3762

Application SPARK PLUG SOCKET - 16mm with TORQUE LIMITER

Ignition

15

Models

NEW

M102, 103

Special swivel 16mm spark plug socket with built in 20Nm torque limiter. 465mm long with T handle.

66US-16

SPARKPLUG SOCKET-MAGNETIC-16mm 16mm (5/8") Sparkplug socket with internal magnet for use on engines with deep seated peanut sparkplugs.

66US-21

SPARKPLUG SOCKET-MAGNETIC-20.8mm 20.8mm (13/16") Sparkplug socket with internal magnet for use on engines with deep seated sparkplugs.

ST7600

TORQUE LIMITER 15-35Nm

M102, 103, 104, 111, 112, 113, 119, 120, 137, 272, 273, 275, 902, 903

M100, 110, 114, 115, 116, 117, 130, 180

All

NEW

OM601, 602, 603, 606

NEW

Adjustable torque limiter for use with 16mm spark plug socket.

ST3047-12

GLOW PLUG SOCKET - 12mm Special deep 12mm socket for removing and installing glow plugs in tight spaces.

B103-0037

SPARK PLUG WIRE PLIERS - EXTRA LONG

All

Use to remove the 'BERU' type wires on late model cars. Wide grip section and special angle make it easy to remove plug wires without separating crimps.

103-0037

SPARK PLUG WIRE PLIERS

All

Use to remove the 'BERU' type wires on late model cars. Wide grip section and special angle make it easy to remove plug wires without separating crimps.

220-0099-33 TEST CABLE - RELAY BRIDGE 16 ampere fused cable for protection of electrical components against faulty contacts

B1630

RESISTANCE SUBSTITUTION BOX

W102, 103, 104, 110.92/98, 99, 111, 112, 113, 116, 117, 119, 120, 137, 601, 602.91/96/97, 615, 616, 617.91/95

NEW

All

Resistance substitution box allows testing and calibration of dash gauges, injection system sensors, cruise control, and anti theft systems. (#1240963)

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 22

www.baumtools.com [email protected]

Section 18 Engine Lubrication

Mercedes Tool Tool Number ST3676

Application OIL DRAIN WRENCH - 14mm HEX X 13mm BOX Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)

ST3677

OIL DRAIN WRENCH - 14mm HEX X 17mm BOX Use to service oil, differential and transmission drain plugs.

KO4012M

OIL DRAIN SOCKET - 14mm Use to remove and install 14mm oil drain plugs in engine and transmission. Sizes available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm.

103-0209

B1407

OIL FILTER WRENCH - 14 POINT 74mm 3/8" DRIVE

18

Models M102, 103, 104, 110, 116, 117, 119, 120, 601, 602, 603, 604, 605, 615, 616, 617

M110, 107, 116, 117, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220, 615, 616, 617, 716, 717 M110, 115, 116, 117, 615, 616, 617

Socket type filter remover for spin on oil filters and filter housings. Reinforced construction and side lock bolts to remove the most stubborn filters. Also see #H2172.

M102, 103, 104, 111, 112, 113, 119, 120, 137, 155, 272, 275, 285, 611, 612, 613, 628, 646, 647, 648

OIL FILTER SOCKET SET

OM364, 366, 604, 605, 606

3 socket set 27mm, 32mm and 36mm for oil filter housings on Mercedes and Smart cars.

B6700

Engine Lubrication

"JAWS" OIL FILTER REMOVER

NEW

All

Special "vise-grip" action makes this the best oil filter remover yet.

H2739G-T50 UNIVERSAL JOINT TORX SOCKET - T50

M112, 113

Use to remove and install TORX bolt on oil pump when removing oil pump with lower oil pan removed. Universal 3/8" square drive, 52mm long bit length. (#112-0010)

120-0621

OIL LEVEL DIPSTICK Use to measure oil level and check length of oil dipstick guide pipe in shop. See #115-1521 for tulip shaped flared oil dipstick guide tubes found in early models.

120-0721

OIL LEVEL DIPSTICK Use to measure oil level and check length of oil dipstick guide pipe in shop. See #115-1521 for tulip shaped flared oil dipstick guide tubes found in early models. See #120-0621 for vehicles 1996-2003.See 275-0021 for 12 cylinder engine M275.

275-0021

OIL LEVEL DIPSTICK Use to measure oil level and check length of oil dipstick guide pipe in shop on new 12 cylinder engines from 2003. See #120-0621 for engines 19962003. Also see #120-0721 for engines from 1997-2006

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M103, 104, 111, 119, 120, OM603, 604, 605, 606

M112, 113, 271, 272, 642, 646, 647, 648

NEW

M275

NEW

www.baumtools.com [email protected] 23

Mercedes Tool Tool Number 111-0034

Engine Lubrication

Application

18

Models

NOZZLE REMOVAL CLAW

M111

Removes oil injection nozzle from crankcase in combination with impact puller #602-0033

604-0034

OIL INJECTION NOZZLE REMOVAL CLAW Use to remove oil injection nozzle from crankcase in combination with impact puller #602-0033.

Mercedes/BMW Fan Service Kit

OM602, 603, 604, 605, 606

NEW

Kit Contains: 32mm - BMW Viscous Fan Nut BMW Pulley Holder #115050 36mm - Mercedes Viscous Fan Nut 65mm - Mercedes Fan Clutch Nut Mercedes Fan pulley holder #113-0040 Mercedes Water Pump holder #103-0040 Fan Belt Service/Idler Pulley Wrench 8mm and 10mm #900-0307

B9042 B1407 OIL FILTER SOCKET SET - 3 socket set 27mm, 32mm and 36mm for oil filter housings on: 27mm - Mercedes and Smart Car 32mm - GM,OPEL/VAUXHALL 4-cyl. GM 2.2liter ecotech X10XE, X12XE, Y17DT, Y17DTL engines, MERCEDES HGV’S e.g. OM364, OM366 engines. 36mm - Mercedes diesel engines OM604, OM605, OM606, BMW engines M52 6-cyl, M60 8-cyl, M70 12-cyl, Mini One/Cooper/Cooper S, Ford 6.0liter diesel engine(predominantly used in pickups), VW VR6 engine.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 24

www.baumtools.com [email protected]

Section 20 Engine Cooling

Mercedes Tool Tool Number 113-0001

Application FAN CLUTCH WRENCH - 36 mm OPEN-END Use to loosen and tighten fan clutch. Use with torque wrench #ST730/5 and holding tool #113-0040.

B113-0001

SPECIAL THIN WRENCH - 36mm

Engine Cooling

20

Models M111, 112, 113, OM604

NEW

All

Use to loosening and tightening of the fan coupling nut. Use with holding tool #113-0040. Also see kit B9042.

120-0201

FAN HUB WRENCH - 65mm Special open-end 65mm wrench for fastening fan hub. Also see kit #B9042.

113-0040

FAN CLUTCH HOLDING TOOL Holds pulley when removing and installing fan clutch. Use with open end wrench #111-0201 and torque wrench #001-7221. (Replaces #119-0240 and #111-0040). Also see kit #B9042.

103-0040

FAN HOLDING TOOL

M103, 104, 119, 120

M111, 112, 113, 119

M103, 104

Use to hold fan pulley while loosening and tightening screws in viscosity fan couplings. Use with tool # 103-0109 or tool # 102-0308. Also see kit #B9042.

B9042

RADIATOR FAN WRENCH SET

NEW

All

This 11 piece wrench set contains 32, 36, & 65mm wrenches for removing fan clutch. Also contains fan clutch holders and V8 fan belt service tools.

ST3049-8

SHORT HEX HEAD SOCKET - 8mm X 24mm LONG 3/8" DR. Removes screws on viscosity fan couplings and pulley facings. (#1030109)

ST1009DC

PULLEY MOUNT BOLT WRENCH - 10mm

M103, 104, 119, 120, 602, 603, 605, 606

M116, 117, 119

Special 10mm Allen wrench 500mm long. Use to loosen and tighten the mount bolts of the idler pulley when adjusting v-belt of refrigerant compressor.

900-0307

A/C IDLER PULLEY ALLEN WRENCH - 8mm x 10mm Special A/C idler pulley wrench allows access to 8mm bolts on 102 and 103 idler pulley, as well as 10mm bolts on 116, 117 V8 models. Also see kit #B9042.

603-0040

PULLEY HOLDING TOOL Use to hold water pump pulley while loosening and tightening screws. Use with tool # 103-0109.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M102, 103, 116, 117

OM602, 603, 604, 605, 606, 611

www.baumtools.com [email protected] 25

Mercedes Tool Tool Number H2740

Application SWIVEL HEX HEAD SOCKET - 6mm 3/8" DR. LONG EXTENSION.

Engine Cooling

20

Models All

Removes and installs water pump hex head bolts.

ST12506

FLEXIBLE HOSE CLAMP HEX NUT DRIVERS

All

Use to remove hose clamps with worm-drive threads. Sizes 5, 6, 7, 8 and 10mm available. Please specify size when ordering. See # H798-5 for late model "Corbin" clamps. 7mm is the most common Mercedes size.

B1027

HOSE CLAMP PLIERS - CORBIN TYPE

All Late Models

Special tips allow easy handling of 'Corbin clamps' on radiator and emission control hoses.

ST10623/1

CORBIN CLAMP PLIERS

NEW

All models

Locking type pliers with rotating jaws to access even the hardest to reach clamps. 290mm Long.

210-0363

RADIATOR CAP ADAPTER

140, 202, 210, 463

Use for testing threaded radiator cap with Stant type tester..

FZ19

RADIATOR ADAPTER - EARLY TYPE

All before 1968

Adapts US type radiator pressure testers to early model radiators with large caps.

FZ20

RADIATOR RESERVOIR ADAPTER This is the radiator reservoir adapter for testing reservoir integrity. Models 1996 And later. (MB #210-589 009100)

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 26

W124, 129, 140, 163, 170, 171, 199, 202, 203, 208, 209, 210, 211, 215, 219, 220, 221, 230, 240, 461, 463, 464

NEW

www.baumtools.com [email protected]

Section 25 Clutch & Pedal Linkage

Mercedes Tool

Clutch & Pedal Linkage

Tool Number

Models

115-0723

C-26

Application CLUTCH GAUGE Inspection gauge for clutch wear.

W107, 123, 124, 126, 129, 140, 163, 170, 201, 202, 203, 208, 210, 460, 461, 463

CLUTCH ALIGNMENT PIN

W124, 201, 203, 170

Center pin for clutch pressure plate. Same as #201-0815.

000-4731

25

UNIVERSAL CLUTCH CENTERING TOOL - 15-28mm Use to center clutch disc with clutch pressure plate

W107, 123, 124, 126, 129, 140, 163, 168, 169, 170, 171, 201, 202, 203, 208, 209, 210, 211, 245.2, 414, 639

NEW

The worlds most advanced pulling technology German by Design

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 27

Section 26 Manual Transmission

Mercedes Tool Tool Number 915-0107

Application DRIVESHAFT GROOVE NUT SOCKET

Manual Transmission

26

Models 716.0/1/2, 717.0/40

Removes the output shaft nut on manual transmissions.

986-1107

MAINSHAFT/JOINT FLANGE GROOVE NUT SOCKET

G72

Removes groove nut on the main shaft and joint flange of manual transmissions.

111-0507

ST51-30

GROOVE NUT SOCKET - MAINSHAFT Removes transmission mainshaft groove nut.

G76/18, G76/18A, G76/27, G76/27A, G76/27-5

DRIVE FLANGE SOCKET - 30mm EXTRA DEEP

711, 716, 717

12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange. Replaces #126-0209.

KO4012M

OIL DRAIN SOCKET - 14mm

716, 717

Use to remove and install 14mm oil drain plugs in manual transmissions. Sizes available 4, 5, 6, 8, 10, 12, 14, 17 and 19mm.

ST3676

OIL DRAIN WRENCH - 14mm HEX X 13mm BOX

716, 717

Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)

ST3677

OIL DRAIN WRENCH - 14mm HEX X 17mm BOX Use to service oil, differential and transmission drain plugs. (#000-2407)

H2756-17

SWIVEL SOCKET-17mm 1/2" DRIVE

M110, 107, 116, 117, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220, 615, 616, 617, 716, 717 All

Use to R&R manual transmission gearbox.

H2756-19

SWIVEL SOCKET-19mm 1/2" DRIVE

All

Use to R&R manual transmission gearbox.

KK70-A

BALL BEARING PULLER SET

All

Complete set of ball bearing extractors for 6000-6013, 6200-621, 63006311 and 6403-6408 type bearings. Replaces #000-9433 and #0010233. Replacement arms available.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 28

www.baumtools.com [email protected]

Mercedes Tool Tool Number KK17-K

Manual Transmission

Application

26

Models

KUKKO BEARING & GEAR PULLER KIT

All

Special reinforced bearing separator and drive cross member for removing bearing inner race from the drive flange on rear wheel bearing. From Kukko of Germany.

KK20-10

GEAR AND BEARING PULLER - SLIDING JAW

All

This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).

KK1-250-P

PULLER ARMS - 250mm LONG (2)

All

Extra long arms for puller #KK20-10 allows removal of bearings and gears from long shafts, such as reverse and 5th gear.

KK22-2

INTERNAL EXTRACTOR COUNTER STAY - LARGE

All

Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.

KK22-1

INTERNAL EXTRACTOR COUNTER STAY - SMALL

All

Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)

KK21

INTERNAL EXTRACTORS

All

Large range of internal extractors for use with #KK22-1 and KK22-2. Sizes range from 5mm to 100mm in diameter.

Internal Extractor Application Chart Mercedes Tool # 000 589 26 33 00

Size 18-23mm

Kukko # KK21-3

000 589 27 33 00

22-28mm

KK21-4

000 589 28 33 00

28-37mm

KK21-5

000 589 29 33 00

36-46mm

KK21-6

000 589 30 33 00

45-56mm

KK21-7

Application Use to pull bearings out of housing. Use to pull bearings out of housing.

Transmission # 717.45/46. 715.5, 722.648, 712 715.32, 715.40, 715.5

Use to pull bearings out of housing. Use to pull bearings out of housing. Use to pull bearings out of housing.

All 716.5, 711.640,/641 716.5, 711.640,/641, 722.8

Use with puller counterstay #KK22-1 or KK22-2. All our pullers are German made by Kukko the OEM choice of all German auto makers.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 29

Section 27 Automatic Transmission

Mercedes Tool Tool Number B7200

Application SHIFT SHAFT BUSHING INSTALLER

Automatic Transmission

27

Models

NEW

All

Use to install nylon shift shaft bushing.

iScanMercedes

MERCEDES BENZ DATA SCANNER

140-1463

MUSHROOM 38 PIN BREAK-OUT ADAPTER

Use to read and reset fault codes, access live data for road tests, activate components and program/code controllers. See inside cover for more details.

Allows easy access to the 38-pin diagnostic socket when using scanners CS2000, CS1000 or with a standard DMM.

1090

TRANSMISSION PRESSURE GAUGE SET Dual gauges allow testing of automatic transmission shift pressures. Kit includes: Two gauges 160psi and 300psi, hook and sufficient hose to bring gauges into car for road tests.(#123-0421).

140-1521

FLUID LEVEL DIPSTICK - TRANSMISSION

722.5, 722.6, 722.7, 722.9

W129, 140, 170, 202, 203, 208, 210, 220

720.1, 722.0, 722,.1, 722.2, 722.3, 722.4, 722.5, 722.6

722.6

Use to determine fluid level of the 722.6 transmission..

168-0121

OIL LEVEL DIPSTICK

716.5, 722.7, 722.8

For determining oil level height.

ST51-30

DRIVE FLANGE SOCKET - 30mm EXTRA DEEP 12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange.

915-0107

DRIVESHAFT GROOVE NUT SOCKET

722.3, 722.4, 722.5, 722.6, 722.9

722.0, 722.1, 722.3

Removes the large type driveshaft nut on automatic transmissions.

915-0807

DRIVESHAFT GROOVE NUT SOCKET

722.0, 722.1, 722.3

Removes the small driveshaft nut.

986-1107

DRIVESHAFT GROOVE NUT SOCKET

K4A025, K4B050

Removes the driveshaft nut on swing axle.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 30

www.baumtools.com [email protected]

Mercedes Tool Tool Number 208-0021

Application CLUTCH PACK COMPRESSOR

Automatic Transmission

27

Models 722.6, 722.8, 722.9

Compresses clutch packs K1, K2, K3 and brake bands B1 and B2. 1000N.

201-0359

201-1243

BRAKE BAND PISTON LOADER Assembly tool for brake band piston B1.

720.1, 722.0, 722.1, 722.3, 722.4, 722.5

SNAP RING ASSEMBLY TOOL

722.3, 722.4, 722.5

Installs snap ring on spring plate for K1, K2, B3.

126-0314

CLUTCH PISTON INSTALLING SLEEVE

722.3, 722.5

Use to guide the clutch piston K1 (127 mm) and K2 into outer disk carrier (Use with sleeve #201-0214).

126-1014

CLUTCH PISTON GUIDE SLEEVE

722.3, 722.5

Use to guide the clutch piston K1 (118 mm) into the outer disk carrier (Use with sleeve #140-0014).

140-0014

CLUTCH PISTON GUIDE SLEEVE

722.3, 722.5

For guiding clutch piston K1 and K2 into the outer disk carrier. (Use with sleeves #126-0314 and #126-1014).

126-0414

REVERSE GEAR PISTON GUIDE SLEEVE

722.3, 722.5

Use to guide the reverse gear piston into front cover.

126-0431

AXIAL PLAY PARALLEL REST

722.3, 722.4, 722.5

Use to measure axial play on front and rear planetary gear set.

129-0623

GAUGING DISK

722.3, 722.4, 722.5

For measuring axial play on rear planetary gear set. (HCB A1037-2)

126-0621

MEASURING SCREW

722.3, 722.5

For checking free travel on brake band piston B1.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 31

Mercedes Tool Tool Number 201-0114

Application CLUTCH PISTON GUIDE SLEEVE

Automatic Transmission

27

Models 722.4

Installs K1 (135mm) clutch piston into outer disk carrier. 4 speed.

201-0214

GUIDE SLEEVE

722.4

Use to guide reverse gear piston into front cover. 4 speed.

201-0721

BRAKE BAND PISTON GAUGE

722.4

Measuring screw with plate for free travel on brake band piston B1.

112-0161

CLUTCH PISTON GUIDE SLEEVE Installs K1 (135mm) 134 ID, 136 OD clutch piston into outer disk carrier.

916-0011

SECONDARY PUMP SCREWDRIVER Use to remove the screw plug on the secondary pump.

KK70-A

BALL BEARING PULLER SET

K4A025, K4C025, K4C025(rein), 722.1

K4C025, K4C025(rein.), W4B025, K4A040, W3A040/270, W3A040/310, W3B050 All

Complete set of ball bearing extractors for 6000-6013, 6200-621, 63006311 and 6403-6408 type bearings. Replaces #000-9933 and #1160733. Replacement arms available.

KK17-K

KUKKO BEARING & GEAR PULLER KIT

All

Special reinforced bearing separator and drive cross member for removing bearing inner race from the drive flange on rear wheel bearing. From Kukko of Germany.

KK20-10

GEAR AND BEARING PULLER - SLIDING JAW

All

This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).

KK1-250-P

PULLER ARMS - 250mm LONG (2)

All

Extra long arms for puller #KK20-10 allows removal of bearings and gears from long shafts, such as reverse and 5th gear.

KK22-2

INTERNAL EXTRACTOR COUNTER STAY - LARGE

All

Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 32

www.baumtools.com [email protected]

Mercedes Tool Tool Number KK22-1

Automatic Transmission

Application

27

Models

INTERNAL EXTRACTOR COUNTER STAY - SMALL

All

Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)

KK21

INTERNAL EXTRACTORS

All

Large range of internal extractors for use with #KK22-1 and KK22-2. Sizes range from 5mm to 100mm in diameter.

SHIFT SHAFT BUSHING INSTALLER

B7200 Special pliers for installing the nylon shift shaft bushing found on most Mercedes models. Also works on Ford, BMW, VW, Audi and other makes.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 33

Section 32 Suspension

Mercedes Tool Tool Number 211-0009

Application SLOTTED SOCKET BIT - 10mm Use to remove and install air suspension line screw joints.

220-0061

AIRMATIC STRUT SEAL REMOVER

Suspension

32

Models 164, W211, 219, 240, 251

NEW

W220

NEW

Use to remove the top seal on the front Airmatic suspension strut.

924-0231

SUSPENSION SPRING COMPRESSOR Compresses front and rear axle springs in the car on models with idler arm and some Macpherson type suspensions. See #H4900 for late model 210, 163, and V class. Telescopic construction range 120mm-325mm.

iScanMercedes

QP1000

MERCEDES BENZ DATA SCANNER Use to read and reset fault codes, access live data for road tests, activate components and program/code controllers. See inside cover for more details.

TORSION BAR SAVER

W116, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 211

W210, 215, 220, 230

W123, 126

NEW

W220

NEW

W163, 164, 171, 203, 209, 210, 211, 219, 230, 245, 251

NEW

All

NEW

W211, 219

NEW

W221

NEW

Torsion bar savers allow replacement of the torsion bar ends with torsion bar still in place in the vehicle.

900-0007

RESIDUAL PRESSURE VALVE SOCKET Use to remove and install the residual pressure valve on front-axle air suspension strut (Airmatic). Double sided tool. 1/4" drive. See #211-0009 for E class. Replaces #220-0009.

1117J

MACPHERSON STRUT SPRING COMPRESSOR Compresses all types of Macpherson style coil springs front and rear. Includes three sets of jaws (2) for 110, 120 and 130mm springs found in most Mercedes.

1117V

MACPHERSON STRUT VICE ADAPTER This vice adapter holds the Macpherson strut when off the vehicle.

211-0763

EMERGENCY BUMBERS FRONT & REAR Use to move vehicle when Airmatic system is disabled during repair.

221-0031

EMERGENCY BUMBERS- SET Use to move vehicle when Airmatic system is disabled during repair.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 34

www.baumtools.com [email protected]

Mercedes Tool Tool Number KK129-0

Suspension

Application

32

Models

UNIVERSAL BALL JOINT PULLER 2-STAGE

All

Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.

H2594

RETAINER WRENCH Oval retainer for front shocks. Use with ST20-17x19 17mm offset wrench to adjust damper tension.

203-0007

SUSPENSION STRUT SOCKET

W107, 108, 109, 111, 113, 114, 115, 116 & 123.

W203

Pin wrench socket for the removal of the suspension strut retainer nut.

ST20-17x19 DOUBLE OFFSET WRENCHS - 75 degree

All

17X19mm - Use with #H2594 to adjust shock absorber damper tension. Special deep offset box end wrenches. Use to adjust shock absorber retainer nuts.

Torsion Bar Saver W123, W126 S-Class Mercedes S-Class W123 and W126 chassises are prone to failure of the torsion bar end. Over time the torsion bar end gets rusty and eventually the thinner part of the bar will break off rendering the vehicle unsafe to drive. Currently the only way to fix this is to replace the entire torsion bar, which is a major undertaking requiring approximately 20 hours. Most customers are unwilling to spend the money to make the repair. With this kit the torsion bar can remain on the vehicle and the job takes about 1 hour (much less with experience).

#QP1000

• First loosen the upper control arm mount on torsion bar. • Next remove the bolt, washer and rubber mount from torsion bar end.

• Cut the torsion bar end off to approximately 1/2” back from the thin section.

• Clean end and weld the Torsion Bar Saver in place. • Install upper control arm outer bushings and tighten. The kit includes new bushings, washers. bolt and special stainless steel repair piece.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 35

Section 33 Front Axle

Mercedes Tool Tool Number B140-1143

Application BEARING RACE AND SEAL RING INSTALLER

Front Axle

33

Models W140

NEW

W170, 202, 208

NEW

W208

NEW

W210

NEW

Installs bearing outer race and radial seal ring of front axle hub.

B202-0143

LOWER CONTROL ARM BUSHING KIT FRONT & REAR - W202 Removal and installation tool for rear rubber mount on the lower wishbone for W170 and W202 chassis. Also installs front mount on W208 chassis.

B208-0043

LOWER WISHBONE REAR MOUNT KIT Use to R&R the rear "hydraulic" type bushing on the lower control arm (wishbone).

B210-0043

LOWER CONTROL ARM BUSHING KIT FRONT & REAR - W210 Puller and installation tool for rubber mount front & rear lower wishbone mount.

126-0143

LOWER WISHBONE REMOVER & INSTALLER TOOL Puller and installation tool for rubber mounts-lower wishbone. Also see #B129-0043.

B220-0643

TORQUE STRUT BUSHING KIT Use to replace the sub frame bushings on the torque strut control rods.

385-0007

GROOVE NUT SOCKET

W116, 123, 124, 126, 201

W171, 203, 209, 211, 215, 220, 230

NEW

W163

NEW

Use to remove and install the retaining nut on the supporting joint of the bottom wishbone in the front and rear axle.

124-0543

BALL BEARING REMOVER & INSTALLER TOOL

W124.2, 124.3

Puller and installer tool for angular ball bearing from steering knuckle. (4MATIC)

220-0061

AIRMATIC STRUT SEAL REMOVER

W220

NEW

W211, 215, 219, 220, 230

NEW

Use to remove the top seal on the front Airmatic suspension strut.

220-0343

BALL JOINT INSTALLATION PRESS Use to install the ball joint into the steering knuckle on late model S, E, CLK, CLS and SL class.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 36

www.baumtools.com [email protected]

Mercedes Tool Tool Number B129-0343

Front Axle

Application

33

Models

LOWER WISHBONE SUPPORT JOINT R&R TOOL

W124, 129, 201

Use to Remove and install lower ball joint support on the wishbone. Replaces #107-0143.

116-0462

BALL JOINT PRESS

NEW

W116, 123, 126

Presses the ball joint into steering knuckle while the knuckle is in place on the car.

KK129-0

UNIVERSAL BALL JOINT PULLER 2-STAGE

All

Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.

KK128-2

TIE ROD BALL JOINT PULLER - 23-32mm

All

Puller for separating tie rod and steering knuckle ball joints without tearing ball joint boots. Mfg. by Kukko of Germany.

Balljoint Installation Presses W116,W123,W126

#116-0462 Use to install the steering knuckle balljoint on W116, W123 and W126 with the knuckle in the car.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

W124,W201,W129

W NE

#B129-0343 Use to install the steering knuckle balljoint on W124, W201 and W129 with the knuckle in the car.

W211,W215,W219,W220, W230

#220-0343 Presses the balljoint into the steering knuckle on W220 as well as W211, W215, W219 and W230 chassis.

www.baumtools.com [email protected] 37

Section 35 Rear Axle

Mercedes Tool Tool Number 203-0043

Application REAR AXLE CARRIER MOUNT BUSHING KIT

Rear Axle

35

Models W203, 209, R171

This tool kit allows easy removal and installation of the rear carrier mount front and rear bushings.

B201-1143

REAR AXLE CARRIER MOUNT REMOVER & INSTALLER KIT

NEW

W124, 129, 201

Puller and installation tool for front and rear rubber mount from rear axle carrier. See #202-0343 for 170, 202, and 208 chassis.

202-0343

REAR AXLE CARRIER MOUNT REMOVER & INSTALLER TOOL

W170, 202, 208

Puller and installation tool for rear rubber mount from rear axle carrier. See #201-1143 for 124, 129 and 201 chassis.

B140-0333

REAR AXLE CARRIER BUSHING MOUNT R & R Kit

NEW

W140, 220

Use to remove and install the front and rear rubber subframe mount on the rear axle carrier.

966-0043

DIFFERENTIAL MOUNT BUSHING REPLACEMENT KIT

W124, 140

Use to remove and install the rear differential mount bushings.

B210-0243

DIFFERENTIAL MOUNT BUSHING REPLACEMENT KIT

NEW

W210

Use to remove and install rubber differential mount bushings in the center of rear axle assembly.

124-0543

385-0007

WHEEL BEARING REMOVER & INSTALLER TOOL Puller and installer tool for wheel bearing in wheel carrier and installation of rear axle shaft flange.

W124, 129, 163, 170, 201, 202, 203, 208, 209 and 210.

GROOVE NUT SOCKET

W163

NEW

Use to remove and install the retaining nut on the supporting joint of the bottom wishbone in the front and rear axle.

915-0207

REAR AXEL BEARING GROOVE NUT SOCKET Rear axel bearing retainer groove nut socket.

915-0107

REAR AXLE FLANGE GROOVE NUT SOCKET Differential drive pinion flange groove nut socket for use on models with constant velocity joint axels.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 38

W107, 114, 115, 116, 123, 126

W107, 114, 115, 116, 123

www.baumtools.com [email protected]

Mercedes Tool Tool Number 111-0507

Application GROOVE NUT SOCKET - SWING AXEL Removes swing axle flange groove nuts.

ST51-30

DRIVE FLANGE SOCKET - 30mm EXTRA DEEP 12 point 1/2" DR. with thin walls and deep broaching for collar nut on drive flange.

201-0009

PINION FLANGE SOCKET - 27mm 3/4" DRIVE Pinion joint flange 12 point socket. Use to remove special retaining nut in late model cars.

ST3004

HEX HEAD SOCKET 12mm XZN X 55mm 1/2"DR.

Rear Axle

35

Models W108, 109, 110, 111, 113

W107, 123, 124, 126, 129, 140, 168, 170, 201, 202, 208, 210, 463

W124, 170, 201, 202, 210

W215, 220

XZN Hex Head Socket-12mm x 55mm 1/2" drive with special short format for rear axle spring link. (119-589-0010)

ST3676

OIL DRAIN WRENCH - 14mm HEX X 13mm BOX Use for oil service on later models requiring longer bit and smaller ring. For oil, differential and transmission drain plugs. (#117-0207)

ST3677

OIL DRAIN WRENCH - 14mm HEX X 17mm BOX Use to service oil, differential and transmission drain plugs.

KO4012M-14 OIL DRAIN HEX HEAD SOCKET 14mm 1/2" DRIVE

W107, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220

M110, 107, 116, 117, 123, 124, 126, 129, 140, 170, 201, 202, 208, 210, 220, 615, 616, 617, 716, 717 All

Short body allows easy removal of oil, differential and transmission drain plugs.

KK21

INTERNAL EXTRACTORS

All

Large range of internal extractors for use with #KK22-1 and KK22-2. Sizes range from 5mm to 100mm in diameter.

KK22-1

INTERNAL EXTRACTOR COUNTER STAY - SMALL

All

Small counter stay for use with Kukko extractor #KK21-0 thru #KK21-5. (#000-3333)

KK22-2

INTERNAL EXTRACTOR COUNTER STAY - LARGE

All

Large counter stay for use with Kukko extractor #KK21-3 thru #KK21-8.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 39

Section 40 Wheels and Tires

Mercedes Tool Tool Number 124-1763

Application WHEEL WEIGHT TOOL

Wheels and Tires

40

Models All

Special tool for the removal and installation of wheel weights.

341C

TOE IN GAUGE

All

Universal toe-in gauge allows quick and easy adjustment of front end toe without the use of a lift.

M0030

WHEEL ALIGNMENT GUIDES

All

Use in place of 2 lug bolts to hold wheel in place while installing other lug bolts 12X1.5mm

M0030A

WHEEL ALIGNMENT GUIDES

All

Use in place of 2 lug bolts to hold wheel in place while installing other lug bolts 14X1.5mm.

B1147-48

WHEEL RING SOCKET SET Special Decagon (10 sided) sockets for removal of triplet aluminum alloy steel ring on special SL wheels.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 40

W230

NEW

www.baumtools.com [email protected]

Section 41 Drive Shaft

Mercedes Tool Tool Number KK20-10

Drive Shaft

Application

41

Models

GEAR AND BEARING PULLER - SLIDING JAW

All

This 2 arm sliding jaw puller is ideal for transmission and differential gears, ball bearings and tapered roller bearings. For applications requiring longer arms see #KK1-250-P for extra long arms (250mm long).

KK1-250-P

PULLER ARMS - 250mm LONG (2)

All

Extra long arms for puller #KK20-10 allows removal of bearings and gears from long shafts, such as reverse and 5th gear.

T9A-46

VERY THIN WRENCH - 46mm Use to remove driveshaft lock nuts. See # T9A-41 Also see #T9A-SET.

T9A-41

T9A-SET

VERY THIN WRENCH - 41mm

107, 108, 109, 111, 113, 114, 115, 116, 123, 126

Use to remove driveshaft lock nuts.

107, 111, 115, 126,

VERY THIN WRENCH SET

All Models

Set of 6 very thin wrenches for use in a variety of situations. Sizes 24mm, 27mm, 32mm, 36mm, 42mm, 46mm

108, 109, 113, 114, 116, 123, 201

NEW

T9A-SET VERY THIN WRENCH SET Set of 6 very thin wrenches for use in a variety of situations, such as, Driveshaft removal, Oil Cooler lines, Camber adjustment, ...etc. Set includes sizes 24mm 27mm 32mm 36mm 42mm 46mm Other sizes available on request.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 41

Section 42 42 Brakes Brakes -- Mechanical Mechanical Section

Brakes

Mercedes Tools Tool Number KK126-00

Application PISTON CALIPER PRESS

42

Models ALL

Use to press calipers back into assembly for easy installation of pads.

KK126-01

BRAKE PAD EXTRACTOR

All

Use to pull out brake pads from caliper body.

KK126-02

BRAKE PISTON CLAMP

All

Use to hold the brake piston/caliper assembly with the brake hose attached during assembly or removal.

KK126-03

BRAKE PISTON TURNING PLIER

ALL

Use to rotate piston caliper during installation.

ST12373

BRAKE CALIPER BRUSH

All

Wire brush for cleaning of fixed brake calipers and shoes.

ST440-14

CROWFOOT SOCKET - 14mm 1/4" DRIVE Use for SBC hydraulic lines.

000-3523

BRAKE PISTON ANGLE GAUGE - 20 DEGREE 38mm & 35mm Use to set the brake piston angle on 35mm & 38mm diameter pistons.

112-0961

BRAKE SPRING INSTALLER

W211, 215, 219, 220, 230, 240

NEW

W107, 114, 115, 116, 123, 124, 126, 129, 140, 201, 202

All

Use to replace parking brake pressure spring.

116-0162

PARKING BRAKE SPRING HOOK

All

Use to remove and install parking brake return spring.

ST3006

BRAKE BLEEDING WRENCH - 9mm

All

Special wrench with attached 100mm hose for quick brake bleeding. 9mm

800-848-6657 Toll Free

800-848-6657 941-927-1414 Intl' 941-927-1612 Fax 941-927-1612 Fax 941-927-1414 Intnl’ 42

www.baumtools.com [email protected]

www.baumtools.com [email protected]

Brakes

Mercedes Tools Tool Number ST4335-11

Application

42

Models

BRAKE BLEEDING WRENCH - 11mm Hollow tubular wrench allows brake line to pass through when bleeding brakes.

ST4335-9

BRAKE BLEEDING WRENCH - 9mm Hollow tubular wrench allows brake line to pass through when bleeding brakes.

H797

BRAKE SPRING PLIERS Use to remove and install brake shoe check spring on glued or riveted brakes. Moveable claw locks in any position desired.

The Terminator Frequency Probe • Sensors Power and Ground of sensors MAP MAF O2 Sensors RPM Sensors Crank Angle Sensor Vehicle Speed Sensors TDC Sensor Idle Switch ABS Wheel Speed Sensors Throttle Position Sensor Cam Position Sensors Air Temperature Sensor Coolant Temperature Sensor Tachometer • • • • •

Electric Relays Motors Actuators Starting & Charging Systems CAN Bus Diagnostics

Ideal for CAN Bus diagnostics Reads: • Voltage • Frequency • Duty Cycle

B7205J

The Terminator is a superior Logic probe combining the features of a DMM and oscilliscope but simplifying the display for technicians that want to find the pulse but don’t need the to see the trace.

800-848-6657 Toll Free

800-848-6657 941-927-1414 Intl' 941-927-1612 Fax 941-927-1612 Fax 941-927-1414 Intnl’

Includes: • Terminator Probe • Ground cable • Extension Cord • extra Probe tips • Storage Box

www.baumtools.com [email protected]

www.baumtools.com [email protected]

43

Section 46 Steering

Mercedes Tool Tool Number

Application

B900-0059K IGNITION AND DASH KIT Kit includes early and late model ignition switch cover grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.

900-0059K

DASHBOARD SERVICE TOOL KIT Ignition Lock Removal Pins - 124, 126, 201, Dash Hooks -107, 116, 123, 124, 126, 140, 201, Radio Removal Keys - 129, 140, 202, 210.

210-0007

IGNITION LOCK COVER REMOVER Special socket for removal of ignition lock cover. Replaces Mercedes #129 589 00 007 00.

202-0014

IGNITION LOCK REMOVING SLEEVE Use to aid in removal and installation of the ignition lock cover. Also see #210-0007

126-0714

IGNITION LOCK COVER REMOVER Rubberized interior allows easy turning of inner lock cover particularly on W126-and 124 chassis. Use with tool # 900-0059.

900-0059

IGNITION LOCK RELEASE WIRES Wires allow depression of lock retainers for easy removal of ignition switch. Use with tool # 126-0714 or #202-0014

H4550-2

CROWFOOT LINE WRENCH - 19mm Use to remove and install high pressure hose at steering pump. (#3140103)

116-0621

STEERING POSITION CHECK SCREW Use to center steering gear for correct positioning of steering wheel during installation.

201-0821

STEERING POSITION CHECK SCREW Use to center steering gear for correct positioning of steering wheel during installation.

201-0621

STEERING POSITION CHECK SCREW

Steering

46

Models W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463

NEW

W107, 123, 124, 126, 129, 140, 201

NEW

W129, 140, 164, 169, 171, 199, 202, 203, 208, 209, 210, 211, 215, 219, 220, 221, 230, 240, 245, 251, 414, W126, 129, 140, 163, 170, 202, 210, 414

W116, 123, 124, 126, 201

W126, 124, 129, 140, 201, 210

W124, 129, 140, 201, 202

W107, 114, 115, 116, 123, 126 (LS90, L1Z)

W107, 114, 115, 123, 201 (LS1, L1Z, LS68)

W124, 201, (LS68)

Use to center steering gear for correct positioning of steering wheel during installation.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 44

www.baumtools.com [email protected]

Mercedes Tool Tool Number 108-0233

Application STEERING PUMP PULLEY PULLER COLLET TYPE

Steering

46

Models All

Short format of this puller allows it to remove the pump pulley without removing hoses or radiators on some models.

202-0133

DRAG LINK PULLER

W202

Use to remove drag link ball joint. Use with pad #129-1063.

KK204-1

PITMAN ARM PULLER

All

Heavy duty puller with reinforcing cross member for removing pitman arms and drag link arms.

KK129-0

UNIVERSAL BALL JOINT PULLER 2-STAGE

All

Scissor type puller allows access to difficult to reach and obstructed ball joints. 2-stage action allows removal of spindles up to 50mm in length. Mfg. by Kukko of Germany.

KK128-2

TIE ROD BALL JOINT PULLER - 23-32mm

All

Puller for separating tie rod and steering knuckle ball joints without tearing ball joint boots. Mfg. by Kukko of Germany.

ST1445

TAMPER PROOF TORX BIT - T30 Special bit for R&R of screws on airbag control units and sensor mounts.

ST1295

TORX - T30 X 90mm LONG ST1295

W124, 126, 129, 201

All Chassis

Use to remove screws holding Airbag cover on steering wheel.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 45

Section 47 Fuel Supply

Mercedes Tool Tool Number 210-0107

Application FUEL TANK SENDER PIN WRENCH - 5mm

Fuel Supply Models

47

W140, 210

Pin wrench for removing and installing lever-type fuel level sensor.

202-0007

FUEL SENDER PIN WRENCH

W202

Use to remove fuel sender retainer nut.

203-0107

FUEL TANK SENDER SPIDER WRENCH

W163, 203

Use to remove and install the locking ring of the fuel tank delivery sensor unit.

163-0037

FUEL PIPE CONNECTION PLIERS

W163, 203

Allows quick release of fuel pipe connections (quick couplers), particularly the fuel pump connection to delivery sensor unit.

202-0190

TANK CAP WITH PRESSURE HOSE

W202

Use to facilitate pressure build-up.

M0035A

GAS TANK SOCKET - 46mm

All

Use to remove fuel tank filter body and fuel gauge sending units.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 46

www.baumtools.com [email protected]

Section 54 Instrument Cluster

Mercedes Tool Tool Number

Application

B900-0059K IGNITION AND DASH KIT Kit includes early and late model ignition switch cover grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.

140-1463

MUSHROOM 38 PIN BREAK-OUT ADAPTER Allows easy access to the 38-pin diagnostic socket when using scanners CS2000, CS1000 or with a standard DMM.

ST1520

KABLEX CONNECTOR KIT - MERCEDES

Instrument Cluster

54

Models W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463

NEW

W129, 140, 170, 202, 203, 208, 210, 220

All

Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor.

140-1321

CLOSED-CIRCUIT CURRENT TEST ADAPTER 2

R129 as of 1.9.95, W140, 163, 168,

For checking closed-circuit current consumption of electric circuit (for maxi- 171, 202, 208, flat pin fuses). 210, 220

140-1221

CLOSED-CIRCUIT CURRENT TEST ADAPTER 1 Closed-circuit current test adapter 1 for testing closed-circuit current consumption of electric circuit

220-0099-33 TEST CABLE - RELAY BRIDGE

B1630

R129 as of 1.9.95, W140, 163, 168, 170, 202, 208, 210, 220

16 ampere fused cable for protection of electrical components against faulty contacts.

W107, 123, 124, 126, 129, 140, 170, 201, 202, 203, 208, 209, 210, 211, 215, 220, 230, 461, 463

RESISTANCE SUBSTITUTION BOX

All

NEW

Resistance substitution box allows testing and calibration of dash gauges, injection system sensors, cruise control, and anti theft systems. (#1240963)

140-0233

INSTRUMENT CLUSTER PULLER HOOKS (2 PIECES) Use to remove and install instrument cluster.

110-0059

PULLING HOOKS - DASH Wide flat hooks for instrument clusters on older models.

129-0109

BULB HOLDING TOOL Use to remove and install socket bulbs in instrument cluster without having to remove complete instrument cluster.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

W124, 126, 129, 140, 168, 170, 201, 202, 208, 210, 463

W107, 108, 109, 111, 114, 115, 116, 123, 125

W129, 140, 163, 170, 202, 208, 210, 220

www.baumtools.com [email protected] 47

Mercedes Tool Tool Number 140-0133

Application

Instrument Cluster

54

Models

MOUNTING LEVER

W124, 129, 140

For module from module box.

Radio Removal Tool Master Kit #B9059M (46 Pieces) This 46 piece kit unlocks the mounts of most radios and GPS units currently in use in domestic and imported vehicles.

1) Kenwood II (1998-2001) 2) Sony II ab 2002 3) Kenwood III (ab 2002) 4) Pioneer & JVC 5) Sony I (since 2001) 6) Panasonic 6A) Panasonic 2006 7) Mercedes Benz & BMW 8) Mercedes Benz & BMW 9) Mercedes Benz & BMW 10) Clarion - New 11) Clarion - Old 12) Fiat Brava 13) Opel 14) Blaupunkt, Grundig, (VW, Audi, Ford) 15) BMW 16) Becker - VW, Audi, Mercedes Benz 17) Becker - Porsche, Mercedes Benz 18) VW 19) BMW, Opel - Linbus 20) Becker - New (since 2002) 21) Skoda - New (since 2002 22) Blaupunkt - New (since 2002) Metal storage case.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 48

www.baumtools.com [email protected]

Section 82 Electrical Equipment

Mercedes Tool Tool Number B57BG-M

Application WIRE TERMINAL AND CONNECTOR CRIMPING - MASTER KIT

Electrical Equipment

82

Models All

NEW

All

NEW

This kit includes the basic crimper and 5 interchangeble MAGNETIC crimping heads. Also has a handy one handed wire stripper. Crimps barrel, butt, hex, coaxial, insulated, non-insulate, closed, flag, & cord end terminals of multiple sizes.

B57BG-E

WIRE TERMINAL AND CONNECTOR CRIMPING KIT- ECONOMY This kit includes the basic crimper and 3 interchangeble crimping heads.

iScanMercedes

DBL800

MERCEDES BENZ DATA SCANNER

All

Use to read and reset fault codes, access live data for road tests, activate components and program/code controllers. See inside cover for more details.

DEUTRONIC POWER SUPPLY/BATTERY CHARGER

All Models.

NEW

All

NEW

All models 19942006

NEW

All models 19942008

NEW

All

NEW

Microprocessor controlled charger/power supply to maintain power levels during programming and diagnostics. Microprocessor controlled charging, measuring and monitoring. Built-in interface for computer, programming unit, printer and large display.

B7205J

TERMINATOR The Terminator is a superior Logic probe combining the features of a DMM and oscilloscope but simplifying the display for technicians that want to find the pulse but don’t need the to see the trace. Particularly useful for tracing CAN signals.

OBD2-300

OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes. Comes with instruction manual with over 2000 fault code definitions.

OBD2-500

OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes live data, freeze frame, ands all SAE OBD-II modes 1 thru 9. SAE1850, ISO and CAN protoccols. Comes with instruction manual with over 2000 mfg. fault code definitions.

V8695

SRS TEST RESISTOR This tool is equipped with the same connector and is of the same resistance as the air bag module. Use to test for faulty airbags.

B1630

RESISTANCE SUBSTITUTION BOX

All

Resistance substitution box allows testing and calibration of dash gauges, injection system sensors, cruise control, and anti theft systems. (#1240963)

900-0059K

DASHBOARD SERVICE TOOL KIT Ignition Lock Removal Pins - 124, 126, 201, Dash Hooks -107, 116, 123, 124, 126, 140, 201, Radio Removal Keys - 129, 140, 202, 210.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

W107, 123, 124, 126, 129, 140, 201

NEW

www.baumtools.com [email protected] 49

Mercedes Tool Tool Number B9059M

Application MASTER RADIO REMOVAL KIT.

Electrical Equipment

82

Models

NEW

All

Contains all tools needed to removve models from 1990 to the present.

929-0105

RADIO REMOVAL TOOLS

1990 and newer

Use to remove and install radios. Also part of #B9059M

ST1520

KABLEX CONNECTOR KIT - MERCEDES

All

Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor.

B900-0059K IGNITION AND DASH KIT Kit includes early and late model ignition switch cover grippers, retainer nut socket (6/97 and newer), ignition lock release pins, dash removal hooks and radio release keys.

129-0005

REMOVAL PLATE (2 PIECES)

W126, 129, 140, 163, 170, 202, 210, 211, 220, 230, 240, 414, 463

NEW

R129

Use for removal of radio Also part of #B9059M

126-0007

ANTENNA SPANNER WRENCH

W107, 123, 126

Antenna mast mounting nut.

KK43-2

BEARING & RACE PULLER

All

Small puller for use on battery terminals, small gears and bearings.

611250

RELAY PLIERS Allows easy removal of 'BOSCH' relays in even the tightest locations.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 50

All

NEW

www.baumtools.com [email protected]

Mercedes Tool Tool Number iScanMercedes

Heating & Air Conditioning

Application MERCEDES BENZ DATA SCANNER

83

Models All from 1988

Use to read and reset fault codes and access live data.

CS2-CMP38 MERCEDES 38 PIN MULTIPLEXER

From 1992-2000

Use with the CS2000 scanner to automatically switch from one system to another, when performing diagnostics. Can only be used with version 3.6F or PV1.21F or later software. Use with B140-1463A for longer extension.

140-1463

MUSHROOM 38 PIN BREAK-OUT ADAPTER Allows easy access to the 38-pin diagnostic socket when using scanners CS2000, CS1000 or with a standard DMM.

B140-1463A 38 PIN X 38 PIN 7' EXT CABLE Extension cable allows use of test equipment while driving or on dynamometer.

203-0010

CONDENSOR FLUID RESERVOIR SOCKET

W129, 140, 170, 202, 203, 208, 210, 220

W124, 129, 140, 202, 208, 210

HOT

W171, 203, 209

NEW

Used to remove and install screw plug on condenser fluid reservoir.

ST440-17

CROWFOOT LINE WRENCH - 17mm 3/8" DRIVE Use to access hard to reach A/C expansion valves.

ST440-19

CROWFOOT LINE WRENCH - 19mm 3/8" DRIVE Use to access hard to reach A/C expansion valves.

ST440-22

CROWFOOT LINE WRENCH - 22mm 3/8" DRIVE Use to access hard to reach A/C expansion valves.

ST440-24

CROWFOOT LINE WRENCH - 24mm 3/8" DRIVE Use to access hard to reach A/C expansion valves.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463

M107, 123, 124, 126, 129, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463

M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463

M107, 123, 124, 126, 140, 170, 201, 202, 203, 210, 215, 220, 461, 463

www.baumtools.com [email protected] 51

Mercedes Tool Tool Number AS4750

Application 5-POINT TAMPER PROOF (TBI) BIT SET

Body - General

B

Models All

NEW

All

NEW

Use on air mass meter elements, transmissions, Ignition locks,

H2715-20H5 T-HANDLE 5PT TAMPER PROOF Use to remove and install mirror mounts.

140-0233

INSTRUMENT CLUSTER PULLER HOOKS (2 PIECES) Use for various assembly/disassembly jobs, such as, removing clipped panels and covers

B2014

PANEL POPPER KIT

W208, 168, 170, 210

All

NEW

All

NEW

Set of 4 panel poppers for removing panels and trim on all types of vehicles.

B2015

PANEL AND TRIM KIT Use this 6 piece set of tools to remove panels and trim without damage.

900-0072

GREASE GUN - DOOR HINGE

All

Use to lubricate door hinges.

B277-477

PLASTIC WEDGE SET

All

Use to remove wood and plastic trim pieces, door panels and dashboard without damage.

T9A-SET

VERY THIN WRENCH SET

All Models

NEW

All

NEW

Set of 6 very thin wrenches for use in a variety of situations. Sizes 24mm, 27mm, 32mm, 36mm, 42mm, 46mm

28DBC

HEAVY DUTY STUD REMOVAL KIT Ideal for pulling threaded studs with a heavy duty impact wrench. Kit includes: bolt, sleeve and 14 collets Collet sizes include: 6x1.0, 7x1.0, 8x1.0 ,8x1.25, 9x1.0, 9x1.25, 10x1.25, 10x1.50, 12x1.25, 12x1.50, 14x1.50, 14x2.0, 16x1.5, 16x2.0mm.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 52

www.baumtools.com [email protected]

Mercedes Tool Tool Number

Application

SDS-BASIC2 STAR BASIC 2 DIAGNOSTIC SYSTEM

Diagnostics

D

Models All from 1988

NEW

All from 1988

NEW

All Models.

NEW

Mercedes Star Basic 2 factory diagnostic system includes DAS. WIS sold separately. Considerably improved over the Star basic.

STAR DIAGNOSTIC SYSTEM - COMPACT 3 SDSCOMPACT3 Mercedes factory diagnostic system. Includes DAS and WIS systems.

DBL800

DEUTRONIC POWER SUPPLY/BATTERY CHARGER Microprocessor controlled charger/power supply to maintain power levels during programming and diagnostics. Microprocessor controlled charging, measuring and monitoring. Built-in interface for computer, programming unit, printer and large display.

140-1463

MUSHROOM 38 PIN BREAK-OUT ADAPTER Allows easy access to the 38-pin diagnostic socket when using scanners CS2000, CS1000 or with a standard DMM.

B140-1463A 38 PIN X 38 PIN 7' EXT CABLE Extension cable allows use of test equipment while driving or on dynamometer.

CS2-CMP38 MERCEDES 38 PIN MULTIPLEXER

W129, 140, 170, 202, 203, 208, 210, 220

W124, 129, 140, 202, 208, 210

HOT

From 1992-2000

Use with the CS2000 scanner to automatically switch from one system to another, when performing diagnostics. Can only be used with version 3.6F or PV1.21F or later software. Use with B140-1463A for longer extension.

iScanMercedes

MERCEDES BENZ DATA SCANNER

All from 1988

Use to read and reset fault codes, access live data for road tests, activate components and program/code controllers. See inside cover for more details.

PUB-2579-00 MERCEDES TROUBLE CODE MANUAL

All

Contains fault codes for self diagnostic systems from 1986 through 2000. Contains all analog and most digital codes for all diagnostic systems.

B7205J

TERMINATOR

All

NEW

All Models from 1996 to the present.

NEW

The Terminator is a superior Logic probe combining the features of a DMM and oscilloscope but simplifying the display for technicians that want to find the pulse but don’t need the to see the trace. Particularly useful for tracing CAN signals.

OBD2-BOB

OBD-II BREAK OUT BOX This J1962 break out box allows access to all wires in the OBD-II / EOBD III Diagnostic Interface This makes it easy to trace CAN Bus faults, Power supply problems and track failed diagnostic controllers.

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 53

Mercedes Tool Tool Number

Diagnostics

Application

OBD2-300

OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes. Comes with instruction manual with over 2000 fault code definitions.

OBD2-500

OBD-II / EOBD FAULT CODE READER Quick scan reads and resets OBD-II and EOBD fault codes live data, freeze frame, ands all SAE OBD-II modes 1 thru 9. SAE1850, ISO and CAN protoccols. Comes with instruction manual with over 2000 mfg. fault code definitions.

909-0021

D

Models

LAMDA CONTROL LOOP TESTER - 100/100IR

All models 19942006

NEW

All models 19942008

NEW

All

Ratio meter for checking on/off ratio and setting CO levels. Includes late models 100/100IR setting. Connects directly to round 8-pin diagnostic plug. Models 1980-93.

LAMBDA CONTROL TESTER

M99

Open/closed loop tester allows analysis on lambda feedback loop. Use to set CO level, check O2 sensor and ECU for proper rich/lean response. Self detects proper wires on 4 wire O2 sensors.

102-0463

TEST HARNESS - EHA Tests CIS-E electronic idle speed control with standard multimeter. (VOMDMM)

All O2 Sensor Equipped

W102, 103, 112, 113, 116, 117

The Terminator Frequency Probe

• Sensors Power and Ground of sensors MAP MAF O2 Sensors RPM Sensors Crank Angle Sensor Vehicle Speed Sensors TDC Sensor Idle Switch ABS Wheel Speed Sensors Throttle Position Sensor Cam Position Sensors Air Temperature Sensor Coolant Temperature Sensor Tachometer • Electric Relays • Motors • Actuators • Starting & Charging Systems • CAN Bus Diagnostics

Ideal for CAN Bus diagnostics Reads: • Voltage • Frequency • Duty Cycle

B7205J

Includes: • Terminator Probe • Ground cable The Terminator is a superior Logic probe combining the features of a DMM and • Extension Cord oscilloscope but simplifying the display for technicians that want to find the • extra Probe tips pulse but don’t need the to see the trace. • Storage Box

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’ 54

www.baumtools.com [email protected]

Mercedes Tool Tool Number ST1520

Application KABLEX CONNECTOR KIT - MERCEDES

KABLEX

Models

K

All

Includes: Round contact pin extractor 1.5mm & 2.5mm, Flat plug contact removers for 2.8mm, 2-prong contacts 5.8mm, 1.6mm Micro-Timer II and !II, 9.5mm Maxi-Power Timer, 5.5, 8,5mm and twin secondary lock device and E-95 extractor.

ST1501/1511 CONTACT EXTRACTOR (ROUND) - 1.5mm

All

Use to remove the round contacts with locking feathers. Replaceable tips available as #ST1511. Also in kit #ST1550.

ST1504/1514 CONTACT EXTRACTOR (ROUND) - 2.5mm

All

Use to remove the round contacts with locking feathers. Replaceable tips available as #ST1514. Also in kit #ST1550.

ST1553

CONTACT EXTRACTOR (FLAT) - 2.8, 5.8mm

All

Use to remove double size flat contacts with single release channel.

ST1591

CONTACT EXTRACTOR (2 PIN DBGM) - 2.8, 5.8mm

All

Use to remove flat plug-in sockets in terminals with two release channels. (#210-0233)

ST1586

CABLE CONNECTOR EXTRACTOR - LARGE TWIN

All

Use to release secondary locking devices of relay panels and junction boxes on DaimlerChrysler models.

ST1584

CONTACT EXTRACTOR (ROUND SOLDERED) - 4.0mm

All

Use to release round soldered terminals from sockets. Center channel allows easy routing of wire without damage.

ST1585

CONTACT EXTRACTOR (ROUND SOLDERED) - 2.5mm

All

Use to release round soldered terminals from sockets. Center channel allows easy routing of wire without damage.

ST1587

CONTACT EXTRACTOR (FLAT) - E-95

All

DBGM, for flat plug-in sockets using E-95 contacts. (#210-0133)

ST1588

FUSE CONTACT EXTRACTOR

All

Use to remove the Grote Hartmann GSK-Flat Fuse Contacts (1-, 2-, 3 terminal version; 2, 4 and 6 locking tongues). (#202-0333)

800-848-6657 941-927-1612 Fax 941-927-1414 Intnl’

www.baumtools.com [email protected] 55

View more...

Comments

Copyright © 2017 KUPDF Inc.
SUPPORT KUPDF